The plane AB is submerged in water has a circular shape as shown in Figure D. The upper edge of the plane is 2.53 m below free surface of water along the wall of the tank. Determine the hydrostatic force of the water on the plane and the position of center of pressure. Neglect the atmospheric pressure.

The plane AB is submerged in water has a circular shape as shown in Figure D. The upper edge of the plane is 2.53 m below free surface of water along the wall of the tank. Determine the hydrostatic force of the water on the plane and the position of center of pressure. Neglect the atmospheric pressure.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A sphere (SG = 2.2) is at the bottom of a tank filled with 1,5m of water. The diameter of the sphere is 50cm. Solve the hydrostatic force on the upper hemisphere. O 2.09kN O 2.73kN O 2.57KN O 3.21kN
7.) The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to the paper and hinge at O. If the depth of water is 2.50 m, neglecting the weight of the gate calculate the horizontal force P to maintain equilibrium. Use unit weight of water 9.80 kN/m^3. Note: change 6 meters arc
Consider the following steady, two-dimensional velocity field: V (1,v) = (0.41 + 2.12)7 + (-3,3 - 2.1y)7 (-33-21)7 Calculate the location of the stagnation point. The location of the stagnation points are x =| and y=
SITUATION. A 35kg disk rests on an inclined surface for which us=0.20 W P A B C 0 Zoom image Determine the reaction at B. a b
An upright isosceles triangular plane surface, with base of 5 ft and a height of 6 ft, is submerged in a liquid of S.G.=0.69. The vertex of the triangular plane surface is located 4 ft below the liquid surface, while the plane of the triangle is inclined at an angle of 35° with respect to the horizontal. Solve for the total hydrostatic force acting on the plane surface and its corresponding location of line of action
6.) The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to the paper and hinge at O. If the depth of water is 2.50 m, neglecting the weight of the gate calculate the distance of the line of action of vertical component of the hydrostatic force on the submerged curved section of the gate from the y-axis. Use unit weight of water 9.80 kN/m^3. fluid mechanics
Two discs are placed in a horizontal plane, one over the other. The water enters at the centre of lower disc and flows radially outward from a source of strength 0.628 m²/y. The pressure at a radius 50 mm is 200 kN/m². Find the pressure at a radius of 500 mm. Also find the stream function at an angle of 300 and 60° if Ø=0 and a=0°. I
Determine the resultant force acting on the face of the sign if qh = 3.70 kPa. The sign has a width of 12 m and a height of 3 m as indicated.
3.78 This dome (hemisphere) is located below the water surface as shown. Detemine the magnitude and sign of the force compo- nents needed to hold the dome in place and the line of action of the horizontal component of force. Here y, = 1 m and y2 = 2 m. Assume T = 10°C. Water Hemi- 2 spherical dome Atmospheric pressure PROBLEMS 3.78, 3.79
An equilateral triangular plate of side 2.4m placed horizontally in a liquid (SG=0.80) in such a way that the center of the plate is 2.5m below the free surface of water. Determine the area if the plate (in sq. meters). Determine the magnitude of the resultant force on the plate. (in kN)
A 285-lb cylindrical tank is at rest as shown. Determine force P required to move the tank up the higher-level surface? (10 Points) r=8 ft 4 ft RA 285 Ibs O 146.54 Ibs O 154.64 Ibs O 144.46 Ibs O 164.54 Ibs
A circular plate of radius 0.75 m is vertically placed in water such that centre of plate is 2 m below the free surface of water. The position of centre of pressure from free surface of water is