The piston rod of diameter 20 mm and length 700 mm in hydraulic cylinder is subjected to compressive force of 10 kN due to the internal pressure. The end conditions for the rod may be assumed as guided at the piston end and hinged at the other end. The Young's modulus is 200 GPa. The factor of safety for the piston rod is

The piston rod of diameter 20 mm and length 700 mm in hydraulic cylinder is subjected to compressive force of 10 kN due to the internal pressure. The end conditions for the rod may be assumed as guided at the piston end and hinged at the other end. The Young's modulus is 200 GPa. The factor of safety for the piston rod is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Adosed cylindrical tank containinga pressurized fluid has an inside diameter of 472 mm and a wall thickness of 10 mm. The tank is pressurized to 240 MPa. Determine the absolute maximum shear stress on the inner surface of the cylinder wall. 40.2 MPa O 295 MPa 35.0 MPa O 272 MPa O 20.9 MPa
STRENGTH OF MATERIALS A boiler is constructed of 9mm thick steel plates that are fastened together at their ends using a butt joint consisting of two 9mm cover plates and rivets having a diameter of 10mm and spaced 60mm apart as shown. If the stream pressure in the boiler is 1.38MPa, determine (a) the circumferential stress in the boiler's plate apart from the steam, (b) the circumferential stress in the outer cover plate along the rivet line a-a, and (c) the shear stress in the rivets. 60 mm 0.78 m
Mechanics of Deformable Bodies. Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1 5 30 mm and d2 5 50 mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC.
The gas storage tank is fabricated by bolting together two half cylindrical shells and two hemispherical shells as shown in Figure 4. The tank and the 25 mm diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4m. If the tank is designed to withstand a pressure of 3 MPa, a. Determine the required minimum thickness of the cylindrical and hemispherical shells b. Determine the minimum required number of bolts for each hemispherical caps. Figure 4
5 - A thin-walled pressure vessel is subjected to internal pressure p = 1 MPa. What is the maximum allowable torque T, applied along the longitudinal axis, if the maximum allowable tensile stress is 80 MPa? -3mm x=3 240ma T polar moment of inertia J=2πr³t
Situation A (1 - 4) A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint . The helical weld makes an angle a = 55° with the longitudinal axis. The vessel has inner radius r= 1.8 m and wall thickness t= 20 mm. The material is steel with modulus E = 200 GPa and Poisson's ratio n= 0.30. The internal pressure p is 800 kPa. Calculate the following quantities for the cylindrical part of the vessel: 1. Calculate the circumferential stress or the cylindrical part of the vessel. А. 72 МPа Helical weld В. 36 МPа С. 24 МPа D. 18 MPa 2. Calculate the longitudinal stress or the cylindrical part of the vessel. А. 18 МPа В. 24 МРа С. 36 МРа D. 72 MPa 3. Calculate the circumferential strain. A. 72 x 106 В. 36 х 10% С. 306 х 10° D. 153 x 10* 4. Calculate the longitudinal strain. А. 72 х 10% В. 36 х 10% С. 306 х 10% D. 153 x 10“
A tapered column assembly is made up from a square tubes having cross-sectional as shown in the figure. The axial loads PA=275KN and PB-3750 kN are applied to the column at levels A and B. Evaluate the axial stress in segment BC of the column. Neglect the self-weight of the structure PA A 150 mm, = 12 mm (1) 150 mm PB 12 = 15 mm %3D (2) 200 mm 200 mm (b) (a) B.
2. The tank shown in the figure is fabricated from steel plate. Determine the minimum thickness of the plate which may be used if the circumferential stress is limited to 40MPa and the internal pressure is 1.5MPA. 400 mm GOO mm
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 12 kips, F₂ = 32 kips, and the normal stress in each rod must be limited to 20 ksi, determine the minimum diameter d₂ required for rod (2). F₂ (1) (2) A O 2.34 in. O 1.63 in. 1.85 in. O 2.20 in. O 3.00 in. d₁ F₂ B -d₂
PROB. 3.7-2 Problems Chapter 3 3.7-2 A motor drives a shaft at 12 Hz and delivers 20 kW of power (see figure). (a) If the shaft has a diameter of 30 mm, what is the maximum shear stress Tax in the shaft? (b) If the maximum allowable shear stress is 40 MPa, what is the minimum permissible diameter d... of the shaft? min 20 kW 341 12 Hz
3. A spherical pressure vessel has a D (mm) inner radius and thickness of 45mm. It is constructed by joining two hollow hemispheres connected by 10nos of 28mm dia bolts along the circumference. Working tensile stress of the vessel is 40 MPa while the tensile stress of the bolt is (o) MPa. (a) What is the maximum allowable internal pressure considering only the capacity of the bolts? (b) What is the maximum allowable internal pressure considering only the capacity of the vessel? (c) What is the maximum allowable internal pressure of the structure in Megapascals Assume: D = 761 σ = 461
a)jj holiow steel tube jsed in a roof structure has an outer diameter, d; = 104 mm and inner diameter, dz = 82 mm. The length of the tube is given by L = 2.75 m and has shear modulus, G = 28 GPa. If the tube is twisted in pure torsion by torques acting at the ends, distinguish the angle of twist when the maximum shear stress, Tmax = 48 MPa.