The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 76 GPa] with a cross-sectional area of A₁ = 820 mm². Bar (2) is a bronze alloy [E = 108 GPa] with a cross-sectional area of A₂ = 520 mm². Assume L₁=1.6 m, L₂=2.0 m, a=0.8 m, b=1.1 m, and c=1.1 m. All bars are unstressed before the load P is applied; however, there is a 1.2-mm clearance in the pin connection at A. If a load of P = 49 kN is applied at B, determine: (a) the normal stresses 61, 62, in both bars (1) and (2). (b) the normal strains £1,2, in bars (1) and (2). (c) determine the downward deflection VA of point A on the rigid bar. (1) A Answers: (a) σ₁ = (b) 1 = (c) VA = i a i i L₁ B b (2) ! ! MPa, 0₁ = ! με, €2 = i mm. i ! MPa. με.

The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 76 GPa] with a cross-sectional area of A₁ = 820 mm². Bar (2) is a bronze alloy [E = 108 GPa] with a cross-sectional area of A₂ = 520 mm². Assume L₁=1.6 m, L₂=2.0 m, a=0.8 m, b=1.1 m, and c=1.1 m. All bars are unstressed before the load P is applied; however, there is a 1.2-mm clearance in the pin connection at A. If a load of P = 49 kN is applied at B, determine: (a) the normal stresses 61, 62, in both bars (1) and (2). (b) the normal strains £1,2, in bars (1) and (2). (c) determine the downward deflection VA of point A on the rigid bar. (1) A Answers: (a) σ₁ = (b) 1 = (c) VA = i a i i L₁ B b (2) ! ! MPa, 0₁ = ! με, €2 = i mm. i ! MPa. με.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A brass (? =5.6 ? 10^6 ???) and aluminum (? = 3.7 ? 10^6 ???) cylinders are bonded together at B, and are attached to fixed supports A and C. Determine (a) The torsion in AB, (b) The torsion in BC, (c) The maximum shearing stress in AB (d) The maximum shearing stress in BC.
An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0×10-6/°C] bar is subjected to a tensile load P. The bar has a depth of d = 260 mm, a cross-sectional area of A = 14720 mm2, and a length of L = 5.5 m. The initial longitudinal normal strain in the bar is zero. After load P is applied and the temperature of the bar has been increased by AT = 46°C, the longitudinal normal strain is found to be 1680 µɛ. % D Calculate the change in bar depth d after the load P has been applied and the temperature has been increased. L P Answer: Ad = i mm
Steel 1 m Aluminum T 0.75 m Determine the maximum permissible value of T subject to the following conditions: tt S 80 MPa, Tal 50 MPa, and the angle of rotation of the free end is limited to 0.1 radian. For T. Hollow Solid d= 30 mm D= 40 mm %3D steel, G = 82 GPa and for aluminum, G= 28 GPa. %3D d = 30 mm %3D
The pin-connected structure shown consists of a rigid bar ABCD and two axial members. Bar (1) is steel [E = 200 GPa; a = 11.7x 10-6/°C], with a cross-sectional area of A1 = 370 mm2. Bar (2) is an aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C], with a cross- sectional area of A2 = 380 mm?. The bars are unstressed when the structure is assembled. Assume a=360O mm, b=620 mm, c=730 mm, P=20 kN, and L=890 mm. After a concentrated load of P = 20 kN is applied and the temperature is increased by 35°C, determine (a) the normal stresses in bars (1) and (2). (b) the deflection of point D on the rigid bar. A (1) B (2)
The pin-connected structure shown consists of a rigid bar ABCD and two axial members. Bar (1) is steel [E = 200 GPa; a = 11.7 x 10-6/°C], with a cross-sectional area of A₁ = 400 mm². Bar (2) is an aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C], with a cross-sectional area of A₂ = 400 mm². The bars are unstressed when the structure is assembled. After a concentrated load of P = 36 KN is applied and the temperature is increased by 25°C, determine (a) the normal stresses in bars (1) and (2). (b) the deflection of point D on the rigid bar. 350 mm 600 mm 900 mm (1) (2) A B 36 kN 720 mm D
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 60 GPa] with a cross-sectional area of A1 = 870 mm?. Bar (2) is a bronze alloy [E = 92 GPa] with a cross-sectional area of Ay = 520 mm?. Assume L$=2.6 m, La=2.9 m, a=0.7 m, b= 1.3 m, and c= 1.1 m. All bars are unstressed before the load P is applied; however, there is a 3.9-mm clearance in the pin connection at A. If a load of P= 58 kN is applied at B, determine: (a) the normal stresses 01, 02, in both bars (1) and (2). (b) the normal strains € , E2, in bars (1) and (2). (c) determine the downward deflection vA of point A on the rigid bar.
Narrow bars of aluminum are bonded to the two sides of a thick steel plate as shown. Initially, at T₁ = 70°F, all stresses are zero. Knowing that the temperature will be slowly raised to T₂ and then reduced to T₁, determine (a) the highest temperature T₂ that does not result in residual stresses, (b) the temperature T₂ that will result in a residual stress in the aluminum equal to 58 ksi. Assume aa = 12.8 x 10-6/°F for the aluminum and a = 6.5 × 10-6/°F for the steel. Further assume that the aluminum is elastoplastic with E = 10.9 × 106 psi and ay = 58 ksi. (Hint: Neglect the small stresses in the plate.) Fig. P2.121
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 65GPa] with a cross-sectional area of A_{1} = 850m * m ^ 2 Bar (2) is a bronze alloy [E = 100GPa] with a cross-sectional area of A_{2} = 540m * m ^ 2 Assume L_{1} = 1.9m L_{2} = 2.2m , a = 0.5m b = 1.6n , and c = 1.3 m. All bars are unstressed before the load P is applied; however, there is a 1.6-mm clearance in the pin connection at A. If a load of P = 55 KN is applied at B, determine: (a) the normal stresses Oj, 62, in both bars (1) and (2). (b) the normal strains E1, E2, in bars (1) and (2). (c) determine the downward deflection VA of point A on the rigid bar
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 30-in.-long bronze [E = 15900 ksi, α= 9.4 × 10−6/°F] bar with a cross-sectional area of 1.00 in.2. Bar (2) is a 48-in.-long aluminum alloy [E = 9200 ksi, α= 12.6 × 10−6/°F] bar with a cross-sectional area of 2.50 in.2. Both bars are unstressed before the load P is applied. Assume L1=30 in., L2=48 in., a=32 in., b=44 in., and c=14 in. If a concentrated load of P = 29 kips is applied to the rigid bar at D and the temperature is decreased by 120°F, determine:(a) the normal stresses in bars (1) and (2).(b) the normal strains in bars (1) and (2).(c) the deflection of the rigid bar at point D. Solve for F2 and F1.Answers: F1 = kips, F2 = kips. Determine the normal stress in each bar. Use positive if tensile, negative if compressive.Answers: σ1= ksi, σ2= ksi. Determine the normal strain in bars (1) and (2). Use positive if tensile, negative if compressive.Answers:…
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 34-in.-long bronze [E = 15000 ksi, α=α= 9.2 × 10−6/°F] bar with a cross-sectional area of 1.75 in.2. Bar (2) is a 42-in.-long aluminum alloy [E = 10300 ksi, α=α= 11.9 × 10−6/°F] bar with a cross-sectional area of 2.25 in.2. Both bars are unstressed before the load P is applied. Assume L1=34 in., L2=42 in., a=30 in., b=42 in., and c=16 in. If a concentrated load of P = 27 kips is applied to the rigid bar at D and the temperature is decreased by 120°F, determine:
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 34-in.-long bronze [E = 15000 ksi, α=α= 9.2 × 10−6/°F] bar with a cross-sectional area of 1.75 in.2. Bar (2) is a 42-in.-long aluminum alloy [E = 10300 ksi, α=α= 11.9 × 10−6/°F] bar with a cross-sectional area of 2.25 in.2. Both bars are unstressed before the load P is applied. Assume L1=34 in., L2=42 in., a=30 in., b=42 in., and c=16 in. If a concentrated load of P = 27 kips is applied to the rigid bar at D and the temperature is decreased by 120°F, determine:(a) the normal stresses in bars (1) and (2).(b) the normal strains in bars (1) and (2).(c) the deflection of the rigid bar at point D.
A two pinned end bars AB (copper) and BC (aluminum) is subjected to a horizontal force P = 90KN applied at pin B %3D as shown in the figure, determine the horizontal displacement of pin B. Aluminum: L= 1.5m, A= 1000mm2, E= 70 GPa Copper: L= 2.0m, A= 850mm², E= 120 GPa Degree: 45° Alumaum L-15m A=1000 mm E-70 GPa >P=90 kN Copper L=2.0m Aa550 mm E=120 GPa