The one-line diagram of a simple power system is shown in Figure below. The neutral of each generator is grounded through a current-limiting reactor of 0.25/3 per unit on a 100-MVA base. The system data expressed in per unit on a common 100-MVA base is tabulated below. The generators are running on no-load at their rated voltage and rated frequency with their emfs in phase. G Stark Item Base MVA Voltage Rating X x² 20 RV 20 kV 20/220 kV 20/220 kV 220 kV 220 kV 220 kV 100 0.15 0.15 0.10 0.10 0.125 0.125 0.30 0.15 0.25 015 0.15 0.05 0.05 100 100 0.10 0.10 0.10 100 100 100 T3 0.10 La 100 0.15 025 0.35 0.7125 A balanced three-phase fault at bus 3 through a fault impedance Zf= jo.I per unit. The magnitude of the fault current in amperes in phase b for this fault is: Select one: A 345.3 B. 820.1 C. 312500

The one-line diagram of a simple power system is shown in Figure below. The neutral of each generator is grounded through a current-limiting reactor of 0.25/3 per unit on a 100-MVA base. The system data expressed in per unit on a common 100-MVA base is tabulated below. The generators are running on no-load at their rated voltage and rated frequency with their emfs in phase. G Stark Item Base MVA Voltage Rating X x² 20 RV 20 kV 20/220 kV 20/220 kV 220 kV 220 kV 220 kV 100 0.15 0.15 0.10 0.10 0.125 0.125 0.30 0.15 0.25 015 0.15 0.05 0.05 100 100 0.10 0.10 0.10 100 100 100 T3 0.10 La 100 0.15 025 0.35 0.7125 A balanced three-phase fault at bus 3 through a fault impedance Zf= jo.I per unit. The magnitude of the fault current in amperes in phase b for this fault is: Select one: A 345.3 B. 820.1 C. 312500

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.49P

See similar textbooks

Similar questions

6. A 3 phase fault occurs at point F as shown in figure. Determine the critical clearing anglefor the system. The generator is delivering 1.0 p.u power under prefault conditio
2A. What is another term for "shunt"? a) in series b) in parallel c) compounded d) none of the above 2B. Which of the following is/are a basic type of DC generator connection? a) series b) shunt c) compound d) all of the above
two alternators A and B having 5% speed regulation are working in parallel at a station. Alternator A is rated at 15 MW while B is at 20 MW. When the total load to be shared is 12 MW, then how much of the load will be shared by the alternator B?
Q2. The single-line diagram of a simple three-bus power system is shown in Figure-2. Each generator is represented by an emf behind the sub-transient reactance. All impedances are expressed in per unit on a common MVA base. All resistances and shunt capacitances are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A three-phase fault occurs at bus 3 through a fault impedance of Zf = j0.19 per unit. (i) Using Th'evenin's theorem, obtain the impedance to the point of fault and the fault current in (ii) Determine the bus voltages per unit. ) j0.05 j0.075 j0.75 2 j0.30 j0.45 Figure-2: Single line diagram of the power system network for Q2 3
A 3 phase fault occurs at point F as shown in figure. Determine the critical clearing anglefor the system. The generator is delivering 1.0 p.u power under prefault condition.
synchronous generator threewThe phases are rated at 1000 kVA and operate at a voltage of 6.6 kV. The product resistance per phase is 0.38 ohms and the leakage reactance is 0.5 ohms per phase. The generator works to provide full load at a power factor of 0.85 delayed and at normal voltages. Find the value of the no-load voltage.
Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit leakage reactance, are connected as a three-phase extended autotransformer bank, as shown in Figure 3.36(c). The low-voltage winding has a 110 volt rating. (a) Draw the positive-sequence phasor diagram and show that the high-voltage winding has a 479.5 volt rating. (b) A three-phase load connected to the low-voltage terminals absorbs 6 kW at 110 volts and at 0.8 power factor lagging. Draw the per-unit impedance diagram and calculate the voltage and current at the high-voltage terminals. Assume positive-sequence operation.
The amplitude of the sinusoidal symmetrical ac component of the three-phase short-circuit current of an unloaded synchronous machine decreases from a high initial value to a lower steady-state value, going periods through the stages of __________ and ________ periods.
Two shunt generators A and B operate in parallel and their load characteristics maybe taken as straight lines. The voltage falls from 240V at no load to 200V at200A, while that of B falls from 245V at no load to 220V at 150A. Determine the bus bar voltage when supplying 66.9KW load. How is the load divided between two generators?
The bus bars of a power station are in two sections A and Bseparated by a reactor. Connected in section A are two 12MVA generators of 15% reactance each and to B, 8 MVAgenerator of reactance 10%. The reactor is rated 8 MVA and15% reactance. Two feeders are connected to bus bar Athrough transformers, each rated at 4 MVA and 5% reactance.Determine the maximum short circuit MVA with which circuitbreakers on the outgoing side of the transformers have todeal.
b) Two synchronous generators, G2 and G2, are connected parallelly supplying a load. Generator G1 has a no-load frequency of 50.5 Hz and a slope of 300 MW/Hz. Generator G2 has a no-load frequency of 50.2 Hz and a slope of 500 MW/Hz. The load consumes 250 MW real power. (1) At what frequency does this system operate, and how much power is supplied by each of the two generators? (ii) An additional 100 MW load is added to this power system. What is the new system frequency, and how much power do G1 and G2 supply? (iii) The governor set point of G2 is changed to control system frequency back to 50 Hz. Determine the G2 governor set point.
In large transformers, the total copper losses may vary from the rated output. % of 0.8 to 1.5 0.2 to 0.6 0.5 to 1 0.4 to 1