All Earth-referenced problems in this section may be solved assuming:REhe = 122 km (entry interface altitude)re = Rɛ + heg = 9.8 m/s?B= 0.1354 km1.225 kg/m= 6378 km6500 km1PsThe Mercury spacecraft was designed to perform a ballistic reentry withinitial conditions6.1Ve = 7.5 km/s (air relative)S = 2.8 m?m =1350 kgCp = 1.5(a) If the maximum design reentry deceleration was to be 8g, what wasthe desired entry flight-path angle for the Mercury spacecraft?(b) At what height did maximum deceleration occur?

Answered: Image /qna-images/answer/1d0e63d5-4ac6-4679-9dca-fe79f12155e6.jpg

The Mercury spacecraft was designed to perform a ballistic reentry with initial conditions Ve = 7.5 km/s (air relative) S = 2.8 m? = U! - 1350 kg Cp = 1.5 %3D (a) If the maximum design reentry deceleration was to be 8g, what was the desired entry flight-path angle for the Mercury spacecraft? (b) At what height did maximum deceleration occur?

The Mercury spacecraft was designed to perform a ballistic reentry with initial conditions Ve = 7.5 km/s (air relative) S = 2.8 m? = U! - 1350 kg Cp = 1.5 %3D (a) If the maximum design reentry deceleration was to be 8g, what was the desired entry flight-path angle for the Mercury spacecraft? (b) At what height did maximum deceleration occur?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

LR = 5m, LG = 2.5m and LC = 1.1m Q2. The Skylark family of sounding rockets consisted of a number of variants (denoted Skylark 5, Skylark 7, and Skylark 12 respectively). These are illustrated on Page 3. The data given below is based on that for the rocket motors they used (all manufactured and named by what was Royal Ordinance – now part of Roxel): Raven XI Motor Total mass: 1280 kg Length = LR See Case Table (units are m) Diameter = 0.44 m Goldfinch IIA Motor Total mass: 420 kg Length = LG See Case Table (units are m) Diameter = 0.44 m Cuckoo IV Motor Total mass: 242 kg Length = LC See Case Table (units are m) Diameter = 0.44 m The payload mass which is additional to the motor masses is to be taken as 100 kg. (a) For the configurations of the three rockets shown on Page 3 in Fig. Q2: (i) Determine the Pitching/Yawing moment of inertia of each rocket about the base of each rocket. (ii) Explain how you could then find the the Pitching/Yawing moment of inertia of each rocket about its…
Given: The plane accelerates in its current trajectory with a= 100 m/s^2 Farag Angle theta= 5° W=105 kips F_drag= 80 kips m= 1000 lbs Find: F_thrust, F_lift Please include the KD. Fthrust Futel t Fueight 000 BY NC SA 2013 Michael Swanbom
- [-/1 Points] DETAILS SERCP8 4.P.006. MY NOTES ASK YOUR TEACHER PRACTICE ANOTHER A freight train has a mass of 1.4 x 10 kg. If the locomotive can exert a constant pull of 8.4 x 105 N, how long does it take to increase the speed of the train from rest to 76 km/h? min Need Help? Read It
Q:1 A model rocket is launched straight upward with an initial speed of 50.0 m/s. It accelerates with a constant upward acceleration of 2.00 m/s? until its engines stop at an altitude of 150 meters. (a) Describe the motion of the rocket after its engines stop. (b) What is the maximum height reached by the rocket? (c) How long after liftoff does the rocket reach its maximum height? ay = 9,8 down (d) How long is the rocket in the air? Signs engines-- cut som I am Sorry !!! 50t
4. A skater with a mass of 60 kg coasting with a speed of 5 m/s approaches a ramp. (a) What is his KE at this point? [E-S-A] KE= '/2 *M y= KE- /z (60K9X5M/s') (b) How much GPE does the skater have as he approaches the ramp? Jno E-S-A necessary (c) As the skater moves up the ramp, (GPE, KE) will be converted to (GPE, KE) (d) How far up the ramp will the skater be able to make it without any extra force added? [E-S-A Round to nearest 0.1
L. y X VA A VB PLANE OF CONTACT BY UBC Engineering On an air hockey table, two pucks of identical mass collide in the middle of the rink. Puck A had an initial m velocity vA 1.9? and puck B had an initial velocity vB = 3.2j The plane of contact can be thought of as a line angled 0 = 34° above the x-axis. If the coefficient of 0.5 between the pucks, what are the velocities of the pucks after the impact? || m according to the x-y axis shown. restitution is e =
HW_5_01P.pdf PDF File | C:/Users/Esther/Downloads/HW_5_01P.pdf 2 Would you like to set Microsoft Edge as your default browser? Set as default To be most productive with Microsoft Edge, finish setting up your Complete setup Maybe later browser. CD Page view A Read aloud V Draw F Highlight 2 of 3 Erase 4. Two blocks mĄ = 3.0 kg and mB = 8.0 kg are on inclines and are connected together by a string as shown in the figure below. The coefficient of kinetic friction between each mass and its incline is uk 0.25. MB m MA 51° 21° Copyright © 2008 Pearson Education, Inc. (a) If ma moves up, and mp moves down, determine their acceleration. (b) What minimum value of µk will keep the system from accelerating? 1:50 PM e Type here to search C A N 2/9/2021
The Reynold's number of a sphere falling in air is 1E6. If the sphere's radius is 1ft, what is its velocity? Density of air is 0.00234 slug/ft³ and viscosity of air is 3.8E-7 lbf-sec/ft²A. 2.5 ft/sB. 5.1 ft/sC. 40.6 ft/sD. 81.2 ft/s
2. Some equations for power that occur frequently in mechanical engineering are Pow = Fv and Pow = Tw Also, recall that 1 Hp = 550ft. Here are some elementary problems to help you improve your facility with units. (a) A model airplane flies at 45 mi/hr in level flight against a drag force of 2.5 lbf. How much power is required to maintain the plane in flight? Express your answer in Hp. (b) A power screw requires a torque of 5 N m to turn at 300 rpm. How much power is required? Express your answer in the appropriate SI derived unit. (c) A generator spins at 3600 rpm. Convert that rotational speed to units of rad/s. (d) A generator spins at 3600 rpm. Convert that rotational speed to units of rev/s. (e) A generator spins at 3600 rpm with a torque of 200 N m. In SI units what is the power? (f) An automobile engine produces 94 kW at 6300 rpm. In SI units, what is the torque? (g) An automobile engine produces 221 lb ft of torque at 1800 rpm. In Hp, how much power does this engine produce?
From rest a balloon begins to rise. the Balloon experiences a lift due to a buoyant force of 8000 N. 1. Total massof the balloon is 600kg. Find Acceleration. 2. The balloon rises a distance of 10m and loses a mass of 50 kg after a weight is thrown off. Find the acceleration of the balloon after this weight loss 3. Find the initial velocity of the mass in the vertical direction at the timeof the jump. 4. After falling 10 m, find the mass' final velocity as it comesinto contact with the ground. 5.What is the total time the mass takes to hit the ground? 6. Find the heightof the balloon when the mass hits the ground 7. The mass lands 3 m from the baloon, find the horizontal velocity required to land 3m from the balloon. 8. Since the balloon exeperiences equal forces when the mass is thrown off, what is the horizontal velocity the baloon experiences during this act and how far does the balloon travel when the mass comes into contact with the ground?
Which of the following need NOT be reflected in a sketch when using the Linear Momentum Equation? a. The direction of the velocities b.Internal forces within the free body diagram c. The boundaries of the control volume d. The pressures at the control sections The following operations may be done on a dimensionless product to obtain other another product without losing its non-dimensionality EXCEPT: a.Adding it to another dimensionless product b.Multiplying it by another dimensionless product c.Impose a constant exponent on it d. Multiplying it by a constant An airplane wing, with chord length of 1.5 m and span of 9 m, is designed to move through standard air (v= 1.51×105 m²/s) at a speed of 7.5 m/s. A 1/10-scale model of this wing is to be tested in a water tunnel (v= 1.00×106 m²/s). If viscous effects govern, what speed is necessary in the water tunnel to achieve dynamic similarity? a.11.33 m/s b.4.97 m/s c.1.51 m/s d.2.98 m/s A dam spillway is to be tested with a 1:20 scale model.…
4. Taylor is practicing for a ping-pong tournament and wants to know how high the ping-pong ball rises above the end of the smooth table after rebounding on the opponent's side. The ping-pong ball has a mass of 2-g and e-0.8. [Ans. To Check: 0.39m] 30° 18 m/s -2.25 m. 0.75 m-