The maximum temperature in the cycle :in ( o C) is A steam power plant operating on ideal Rankine cycle between high and low pressures of 2000 kPa and 25 kPa. The generated power from turbine is 5 MW. The quality of the exit steam from turbine is 90%.

The maximum temperature in the cycle :in ( o C) is A steam power plant operating on ideal Rankine cycle between high and low pressures of 2000 kPa and 25 kPa. The generated power from turbine is 5 MW. The quality of the exit steam from turbine is 90%.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

9MPa pressure and 600C to steam high pressure turbine to ideal Rankine cycle with reheatit enters at high temperature and leaves as saturated steam. Steam is low at 500C by reheating.pressure enters the turbine and condenses in the condenser at 7kPa. If the mass flow is 150 kg / sFind the net power, heat transferred in intermediate heating and thermal efficiency.
A 300 MW steam power plant, according to the simple ideal Rankine cycle references Water vapor enters the turbine at a pressure of 10 MPa and a temperature of 500°C; 10 KPA expands to condenser pressure.Isanthropic of turbine and pumpaccording to the efficiency of 85%, the degree of dryness of steam at the turbine output, find the thermal efficiency of the cycle and the mass flow of water vapor circulating in the cycle.
The net power of a steam power plant operating on the simple ideal Rankine cycle is 30.5 MW. Water vapor enters the turbine at a pressure of 7 MPa and a temperature of 500 °C, expanding to a condenser pressure of 10 kPa in the turbine. The steam is condensed in the condenser by cooling with water supplied from a lake. The flow rate of the lake water is 1950 kg/s. Get 87% of pump and turbine adiabatic efficiencies. Show the cycle in the T-s diagram. ( Cwater=4.18 kj/kg°C ) a) Calculate the thermal efficiency of the cycle. b) Calculate the flow of steam circulating in the loop. c) Calculate the temperature rise of the coolant.
In a Rankine cycle, steam enters the turbine at 2.5 MPa and condenser at 50 kPa, what is the thermal efficiency of the cycle?
plz answer this ASAP A steam power plant operates on the ideal Rankine cycle principle (see installation schematic and T-s diagram below). Water vapor enters the turbine at 15 MPa and 500°C and is condensed at a condenser pressure of 10 kPa. Calculate the thermal efficiency of the cycle.
Open feed water heater in the power plant operating according to the Rankine cycle with ideal intermediate steam is used. Turbine inlet state is 10MPa 650C. Condenser pressure is 10 kPa. Intermediate steam taking takes place at a pressure of 2 MPa. The intermediate steam mass flow rate depends on the total mass flow. Find the ratio. Find the thermal efficiency. TIP: Treat the mass flow entering the turbine by saying 1, and r for the intermediate steam. Result: r = 0.239, yield 45.2%
In a reheat cycle steam at 15 Mpa, 540°C enters the engine and expands to 1.95 Mpa. At this point the steam is withdrawn and passed through a reheater. It reenters the engine at 540°C. Expansion now occurs to the condenser pressure of 0.0035 Mpa. (a) For the ideal cycle, find ee (b) A 60,000 kW turbine operates between the same state points except that the steam enters the reheater at 1.95Mpa and 260°C, departs at 1.8 Mpa and 540°C. The steam flow is 147,000 kg/hr; generator efficiency is 96%. For actual engine, ek, mk, and nk, (c) Determine the approximate enthalpy of the exhaust steam if the heat lost through the turbine casing is 2% of the combined work.4. Steam at 200 bar, 760°C enters the thrott
A power plant operating in a Reheat Rankine Cycle produces steam at 3 MPa, 600oC in the boiler. It keeps the condenser at 45oC by transfer of 10 MW out as heat transfer. The first turbine section (high-pressure) expands to 500 kPa and then flow is reheated followed by the expansion in the low-pressure turbine. Provide a detailed solution. Avoid shortcuts. Solve for the High-Pressure and Low-Pressure Turbines work output (kJ/kg)
In a Rankine Cycle, steam enters the turbine at 2.5 MPa and condenser of 50KPa.What is the thermal efficiency of the cycle?
In a reheat cycle steam at 15 MPa, 540 ̊C enters the engine and expands to 1.95 MPa.At this point the steam is withdrawn and passed through a reheater. It reenters the engineat 540 ̊C. Expansion now occurs to the condenser pressure of 0.0035 MPa (a) For theideal cycle, find e. (b) A 60,000 kw turbine operates between the same state piontsexcept that the steam enters the reheater at 1.95 MPa and 260 ̊C, departs at 1.8 MPa and540 ̊C. the steam flow is 147,000 kg/hr, generator efficiency is 96%. For actual enginefind ek, mk, and nk.
In an ideal Rankine cycle the boiler pressure is 10 MPa. All components are operating at steady state and adiabatically. The steam enters the turbine at 550oC. The condenser pressure is 15 kPa. Determine the cycle efficiency.Find the entropy generation for the condenser for 6 kg/min mass flow rate of steam. This is a Thermodynamics question. Please explain all steps and write nicely. Thanks.
A power plant operating in a Reheat Rankine Cycle produces steam at 3 MPa, 600oC in the boiler. It keeps the condenser at 45oC by transfer of 10 MW out as heat transfer. The first turbine section (high-pressure) expands to 500 kPa and then flow is reheated followed by the expansion in the low-pressure turbine. Provide a detailed solution. Avoid shortcuts. Show how much is the net power output (kW)