The load voltage waveform of a single phase full bridge inverter supplied from 300V DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load values are 2N and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 .008 .014 ,02 .01 Time (sec) .012 .016 .018 a. Find the RMS values of the load voltage and the load current b. Calculate and draw the voltage across the load inductance c. Calculate and draw the source current and find its average value

The load voltage waveform of a single phase full bridge inverter supplied from 300V DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load values are 2N and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 .008 .014 ,02 .01 Time (sec) .012 .016 .018 a. Find the RMS values of the load voltage and the load current b. Calculate and draw the voltage across the load inductance c. Calculate and draw the source current and find its average value

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. A single-phase to single-phase cycloconverter "bridge type" with input voltage and frequency 150V and 50Hz. respectively. The output frequency is 10Hz and the firing angle equal to 45°. The load is resistance with the value of 1002 in series with reactive inductance of the value of 20mH. Assume the extinction angle equal 180°. a. Draw the waveforms output voltage, output current, source current, the thyristors currents (iT, IT, IT and in) b. Calculate the rms of output voltage. c. The rms current of each thyristor. d. The input power factor
Question 2 a) Briefly explain the de chopper, inverter, controlled rectifier and ac voltage controller. b) A buck-boost regulator as shown in Figure 2 has an input voltage, Vs = 12 V. The duty cycle, k = 0.35 and the switching frequency is 30 kHz. It also has an inductance, L = 200 µH, filter capacitance, C = 440 µF. The average load current, Ia 1.25 A. Determine the: i. average output voltage, Va, ii. peak-to-peak output ripple voltage, AVc, iii. peak-to-peak output ripple current of inductor, AI, iv. peak current of the transistor, Ip, V. critical values of L and C, and vi. critical values of L and C if Vs is increased to 14 V. Estimate the change in percentage for the critical values of L and C. is Vs C Load Vo, Vs VC i, Ia Figure 2
Q2 (a) Figure Q2(a) shows a single-phase full-bridge square-wave voltage source inverter has resistor (R) and inductor (L) load of 10 Q and 5 mH respectively connected in series. The inverter output frequency is 50 Hz. The transistor switching scheme is complementary bipolar. (i) Draw the output voltage and current waveforms. (ii) Obtain an expression of the rms output voltage at the fundamental frequency. (iii) If the fundamental AC output voltage is 220 V, find the required DC input voltage for the inverter. (iv) Find the instantaneos load current by considering until the 9th harmonics number. (v) Calculate the total harmonics distortion (THD) of the load current. Use only the first three odd harmonics. (vi) Sketch the harmonics spectrum for output current. (vii) Show the displacement angle a, if 5th harmonic is to be eliminated.
iv. For six-phase half-wave rectifier circuit, the preferred circuit from the point of harmonics reduction in the supply currents is: (a) Simple six-phase half-wave circuit. (b)Double-star six-phase half-wave circuit. (c) Six-phase fork connection circuit. v. The DC supply of single phase bridge inverter is 350V. For quasi-square wave output voltage with a 70 percent ON time and frequency is 50HZ, the RMS value of output voltage is: (a) 292.8V (b) 220.5V (c) 250.6V
FETs have similar properties to ___. a. Scotty diodes b. NPN transistors c. PNP transistors d. uni-junction transistors
Find the critical points and sketch the VTC.We have to find vtc so no need of vin.
How do we know current flows in source terminal? Is this common for n-type mosfet? What is an n-type mosfet?
VoO for Ma mosfet Nn Cox ( )= Jm Alv? ,Vrw=0,7V J00NA (+) VX %3D %3D a) In uhat condition does the mosfet work ?and frnd the voltage Vx= ? M1 3V b) what is the mompmum Voo voltage and why'?
Explain the PWM control and duty cycle generation in phase-control of SCR
To lit the segment on for Common anode is O a. Connect A to +Vcc and give logic 0 to K O b. Connect A to 0 and give logic1 to K O. Connect A to +Vcc and give logic 1 to K O d. Connect A to 0 and give logic1 to K
In a single phase VSI bridge Inverter, the load current is Io =200 sin(wt-45°)mA. The d.c. supply voltage is 220 V. What is the power drawn from the supply ?
Q2. A) What are the main differences between the three-phase bridge 180 and 120 degree modes of conduction? B) What is a single-phase current source inverter?