The interior column of an industrial building supports a roof dead load of 55 psf and a snow load of 35 psf. The column is 25 feet long. The bottom end is fixed, and the top end pinned. In addition, it is braced by struts at a point 6 feet down from the column top as shown to the right. The columns has a tributary area of 1800 square feet. The structure is braced in both the xx and yy planes of the column. Select the lightest suitable W-shape of A588 Grade 50 steel using ASD. Prob 5

The interior column of an industrial building supports a roof dead load of 55 psf and a snow load of 35 psf. The column is 25 feet long. The bottom end is fixed, and the top end pinned. In addition, it is braced by struts at a point 6 feet down from the column top as shown to the right. The columns has a tributary area of 1800 square feet. The structure is braced in both the xx and yy planes of the column. Select the lightest suitable W-shape of A588 Grade 50 steel using ASD. Prob 5

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a) The floor system shown is subjected to a total uniform distributed load of 12 KN/m². Sketch the loading that acts along the members DE and BDG. -2.0 m - 3.0 m- A 3.0 m D E 5.0 m F G
• Use NSCP 2015. Problems: 1.) A floor system consists of a 100mm concrete slab supported by continuous T-beams with 9 m spans, 1.2m 0.c. Web dimensions, as determined by negative-moment requirements, are bw = 280 mm, and d = 500 mm. Concrete cover is 70mm from the centroid of the bars. The beam is subjected to a maximum positive factored moment of 1080 kN-m. Use f'c = 21 MPa and fy = 415 MPa. Calculate the required tension steel area at the point of maximum positive moment.
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is inclined I V: 4 H and distance between trusses is equal to 6 m. The purlin has a weight of 79 N/m and spaced at 1.2 m. on centers. The dead load including the roof materials is 720 Pa, live load of 1000 Pa and wind load of 1.2 1.2 1440 Pa. Coefficient of Purlins pressure at leeward and windward are 0.6 and 0.2 respectively. Assume all loads passes through the centroid of the section. Truss Properties of C 200 x 76 mm Sx = 6.19 x 104 mm Sy = 1.38 x 104 mm W = 79 N/m 12 12 1.2 I Allowable bending stress Fbx= Fby = 207 MPa Truss %3D 6m O Calculate the bending stress, fox, for dead load and live load combination (D+ L). Calculate the bending stress, foy, for dead load and live load combination (D + L). O Calculate the maximum ratio of actual to the allowable bending stress for load combination 0.75 (D + L + W) at the windward side. fbx = 151.14 MPa fby = 169.6 MPa Interaction = 1.25
2. The cross-sectional area of each member of the truss is 1200 mm?. Calculate the stresses in members EF, AF, and BF.
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is inclined I V : 4 H and distance between trusses is equal to 6 m. The purlin has a weight of 79 N/m and spaced at 1.2 m. on centers. The dead load including the roof materials is 720 Pa, live load of 1000 Pa and wind load of 1.2 1.2 1440 Pa. Coefficient of Purlins pressure at leeward and windward are 0.6 and 0.2 respectively. Assume all loads passes through the centroid of the section. Properties of C 200 x 76 mm Sx = 6.19 x 104 mm Sy = 1.38 x 104 mm3 W = 79 N/m 1.2 Truss 1.2 12 12 1.2 Allowable bending stress Fbr = Fby = 207 MPa Truss %3D 6m O Calculate the bending stress, fox, for dead load and live load combination (D + L). Calculate the bending stress, foy, for dead load and live load combination (D + L). O Calculate the maximum ratio of actual to the allowable bending stress for load combination 0.75 (D + L + W) at the windward side. fbx = 151.14 MPa fby = 169.6 MPa Interaction = 1.25
What is the value in kips of the axial force in Column C2 on the first story? Floor System All question pertain to the following floor plan. The floor load is 60 lb/ft?. Ignore the self weight of the members. The building is three stories tall. I- I- I- GZ 20 10! C2 B1 ze lo' to I. エ- 30' 25
A mechanical support framing system is shown below. The framing consists of steel floor grating over steel beams and entirely supported by four tension hangers that are connected to floor framing above it. It supports light machinery with an operating weight of 4000 lbs, centrally located. (a) Determine the impact factor I from the Live Load Impact Factor, (b) Calculate the total live load acting on one hanger due to the machinery and uniform live load of 40 psf around the machine. (c) Calculate the total dead load acting on one hanger. The floor framing dead load is 25 psf. Ignore the weight of the hangers. Lateral bracing is located on all four edges of the mechanical floor framing for stability and transfer of lateral loads.
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm
Determine the reactions of A & B for the steel bon and leasing as given abuming that 4.5 mm clearance exist bin the bar and the ground before the loads are applied. Assume E = 200 GPG. P₁ = 300 KN P₂ = 600 KN A₁ = 250 mm² A₂ = 400 mm² 5 R 4 3 2 1 & P VA 0 B P₂ 150mm 150m 150mm 150mm 4.Sm
Situation. A flooring system consists of parallel I-beam sections spaced at 3 m. on centers simply supported over a span of 9 m. The beam supports a 200 mm thick concrete slab of ultima strength fc = 21 MPa. The flooring system is designed for as ceiling and floor load of 750 N/m². The properties of the I-beam sections are: A = 11,500 mm² d = 350 mm; tw = 10 mm bf = 250 mm; t+= 16 mm lx = 266x105 mm4 ly = 45 x 105 mm4 fy = 248 MPa Wb = 90 kg/m fy = 248MPa Calculate the service floor live load (kPa) each beam can sustain in bending under allowable stress design method. Select the correct response: 7.05 2.91 C CUN 2.21 1.92
The lateral load resisting system of the below building is 25 ft (E) H. 25 ft 25 ft 25 ft 25 ft 25 ft 25 ft ↑ 3 North 4 5 Key: = Moment Resisting Frame Floor Framing Plan dual system moment frame shear wall braced frame 25 ft 25 ft 25 ft 25 ft 25 ft
6.D1 A large tower is to be supported by a series of steel wires; it is estimated that the load on each wire will be 13,300 N (3000 Ib). Determine the minimum required wire diameter,assuming a factor of safety of 2 and a yield strength of 860 MPa (125,000 psi) for the steel.