The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the position shown. Member BD is 15 mm thick and is connected at Cto the vertical rod by a 9-mm-diameter bolt. Know that P= 2.8 kN and e = 75°. 100 mm- 175 mn D B 20 200 mm F 45 mm Determine the bearing stress at Cin member BD.

The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the position shown. Member BD is 15 mm thick and is connected at Cto the vertical rod by a 9-mm-diameter bolt. Know that P= 2.8 kN and e = 75°. 100 mm- 175 mn D B 20 200 mm F 45 mm Determine the bearing stress at Cin member BD.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

0 Required information The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. The modulus of rigidity is 3.1 x 106 psi for aluminum and 5.2 x 106 psi for brass. If T = 16 kip in, a-1.1 in. and b=2.2 in., determine (a) The reaction torque at A (b) Maximum shear stress in BC T 12 Assuming the reaction torque at A is TA (kip.in)(4). TA<16(kip.in) express the magnitude of (1) the internal reaction torque from A to B as TAB ([ ) (kip.in) (i) the internal reaction torque from B to C as TBC ) (kip.in) TA+ TA+
A force P of magnitude 950 N is applied to the pedal shown. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 9 mm T 5 mm A 75 mm 125 mm ↓ B 300 mm D Determine the corresponding bearing stress in each support bracket at C. The corresponding bearing stress in each support bracket at Cis MPa.
d = 30 mm diameter, solid, ductile no.11 m from end A of vertical shaft AB made of materialtightly fitted to a radius disc, at end B to the groundfixed. From the C point of the disk - parallel to the y axisA force of F = 20 kN will be applied. Safety of the shaftcontrol according to Tresca criterion and Von-Mises criteriondo. (Due to the tight fit, the shaft is in the hole in the disc.cannot rotate freely.)
The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys Band Care as shown. Take a = 1.4 m, b= 0.9 m, and G= 27 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 300 N. m 200 N. m 45 mm 44 mm 40 mm Im Determine the angle of twist between Band C. The angle of twist between Band Cis|
A flange coupling connects two shafts in order to transmit 250 kW at 100 rpm. It uses 6 bolts with a diameter of 20 mm located at a 210 mm bolt circle diameter. Determine the flange thickness if the bearing stress on the flange is 95 MPa. A. 10 mm B. 20 mm C. 25 mm D. 30 mm
find the bearing stress between bolts and plate 10/-.. 5. 1) 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 1O MM ------- -O- O 300mm 8 mm
A square key is to be used in a 40 mm diameter shaft and that will develop a 2 kN-m torque. If bearing stress of the key is 400 MPa, determine the cross sectional area of square key in mm2 to be used if key length is 30 mm.
15. Given a front hand brake of a bicycle. The applied force, P = 70 N and the equivalent area and length of the cable is 1.02 mm² and 460 mm respectively. If the elongation of the cable is found to be 0.225 mm, find the normal stress in the cable. a. 137 b. 153 Brake cable, L= 460 mm a. 782 b. 784 37.5 mm/A 50 mm Hand brake pivot A -100 mm- C. d. 168 195 P (Resultant of distributed pressure) 16. How much should an 80-kg person weigh (in Newtons) if he is on top of Mt. Kilimanjaro, which is at 5890 m above sea level? The mass and radius of the earth are 5.9742 x 1024 kg and 6378 km, respectively. Use a universal gravitational constant of 6.67 x 10-¹1 m³/kg-s² C. 786 d. 788 Uniform hand brake pressure
For the structure shown, design the maximum permissible value of W using a factor of safety of 2, based on the following conditions. a. Ultimate normal stress in members CD and EF is 140 ksi. b. Ultimate shear stress in pins B, D, F, and H is 100 ksi. c. Ultimate bearing stress on member ACEG is 200 ksi. d. Ultimate bearing stress on support plates at B and H is 240 ksi. All members have dimensions of 5 x 2 in while the support plates have 1.5 in. thickness. Pins at B and H have 1 in. diameter while pins C, E, D, and F have 3/4 in. diameter. Note that there are two identical members CD and two identical members EF. Also, there are two support plates in B while only one plate is used in H. W A B 13 ft- 3 3 10 ft- 4 ft -3 ft-
17. The frame shown carries a load P = 2000 lb. If a = b = 10 inches, c = 18 inches, and s= 3/8 inch. Determine the stress in strut BD in ksi. a. 30.5 b. 34.2 a b PA D B C. d. 39.0 46.1 C 22 24 section A-A: Is 18. The motion of the follower of a cam-follower system is governed by x = R(1 + 1/2 cosoot). If R = 70 mm and co = 62.8 rad/min, determine the magnitude of the acceleration of the follower, in mm/s², when t = 0.8 s. a. 18 C. b. 20 d.
A pulley is keyed to a 2.5 in diameter by means of a 5/8’’ x 7/16’’ x 3’’ flat key. The allowable bearing stresses for the key, hub and shaft are 66 ksi, 59 ksi and 72 ksi, respectively. Determine the maximum power that the pulley can safely transmit at 300 rpm.
The homogenous bar that weighs 5000 Ib is supported by a pin at Cand a cable that runs from A to B around the frictionless pulley at D. If the diameter of the cable is 0.8 inch, calculate its axial stress. Express your answer in ksi (kips per sq. inches) with one decimal place only (Note: Give only the numerical value of the answer. DO NOT INCLUDE THE UNIT IN THE ANSWER) * D F 3 ft 5 ft 5 ft