The grinder has a force of 400 N in the direction shown at the bottom. The grinder has a mass of 300 kg with center of mass at G. The wheel at B is free to move (no friction). Determine the force in the hydraulic cylinder DF. Express in Newtons below. 150 D E $T 600 450 -1300- 380 Fa B G MA -900- Dimensions in Millimeters 200500500- PALA F 20°

The grinder has a force of 400 N in the direction shown at the bottom. The grinder has a mass of 300 kg with center of mass at G. The wheel at B is free to move (no friction). Determine the force in the hydraulic cylinder DF. Express in Newtons below. 150 D E $T 600 450 -1300- 380 Fa B G MA -900- Dimensions in Millimeters 200500500- PALA F 20°

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.73P: The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the...

See similar textbooks

Similar questions

The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions l1 = 0,31 m ja l2 = 0,23 m Determine the support force on the rear tire.
The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions: l1 = 0,31 m and l2 = 0,23 m Determine the support force on the rear tire.
2250 2040 1080 COOPER FEETF 10-1 Dimensions in millimeters The three feller cuts off large trees near ground level and then continues to grasp the trunk. Determine the force in hydrolic AB for the position shown if the tree has a mass of 3 Mg. Determine the required pressure on the 120 mm diameter piston of cylinder.
Pl6-L Set up the relative velodity equalion between points A and B. -3m
2. The backhoe supports a 7.5 kN weight of soil in the bucket which has a center of gravity at G. Find: 0.64 m 0.25 m ● 0.26 m 0.3 m 1.68 m Force in cylinder ED (indicate if force is in tension or compression) Force in cylinder FI (indicate if force is in tension or compression) OF 0.4 m 0.1 m A -1.44 m- 17.5 kN 0.25 m D B m E 0.22 m 0.45m H O SUSIS Force in ED = Force in FI = KN (Tor C) kN (Tor C)
1-20. Determine a set of three rectangular compo- nents of the 242-lb force shown in Fig. Pl-20. 242b P1-20
The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the pressure in pounds per square inch (psi) and r represents the radial distance in inches. Determine the torque C required to operate the sander at constant speed if the kinetic coefficient of friction for the surface being sanded is 0.86.
Solve Prob. 7.29 if =0.
A truck is driving over a scale at a weight station. When the front wheels drive over the scale, the scale reads 5800 N. When the rear wheels drive over the scale, it reads 6500 N. The distance between the front and rear wheels is 3.20 m Determine the distance between the front wheels and the truck's center of gravity.
The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined at 20o with the horizontal. If the 100-N pull is then removed, find the distance the block will travel. the answer must 3 decimal places.
Solve the missing angle and weight and draw the body diagram
A tree feller cuts off large tree near the ground level and then continues to hoist the trunk. If the tree has a mass of 3 tonne (i.e. 3 metric ton), for the position shown 180 C B 1080 2250 2040 720 Determine the bar the pressure in hydrauliç cylinder AB. Answer: