The grains of wood in the board make an angle of 20°with the horizontal as shown. The board is subjected toan axial load of P = 300 N. (Figure 1)Part ADetermine the normal stress that acts perpendicular to the grains.Express your answer to three significant figures and include the appropriate units.µAValueUnitsSubmitRequest AnswerFigure< 1 of 1Part BDetermine the shear stress that acts parallel to the grains.Express your answer to three significant figures and include the appropriate units.HA-300 mm160 mmTa'y =ValueUnits20°25 mm1SubmitRequest Answer

The grains of wood in the board make an angle of 20° with the horizontal as shown. The board is subjected to an axial load of P = 300 N. (Figure 1) Part A Determine the normal stress that acts perpendicular to the grains. Express your answer to three significant figures and include the appropriate HA Value Units Submit Request Answer

The grains of wood in the board make an angle of 20° with the horizontal as shown. The board is subjected to an axial load of P = 300 N. (Figure 1) Part A Determine the normal stress that acts perpendicular to the grains. Express your answer to three significant figures and include the appropriate HA Value Units Submit Request Answer

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
Estimate the transverse tensile strength of the concrete in Problem 12.6.
2. The manufactured wood beam carries the concentrated loads shown. What is the maximum safe value of P if the working stress in shear is 6 MPa? 20 mm 80 mm |3P 2 m 2 m 70 mm B 160 mm -- NA I = 15.52 × 106 mmª 1.0 m 1.0 m 20 mm
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?
3. The manufactures wood beam carries a uniformly distributed load of intensity wo Determine the largest safe value of w, if the shear stress in the wood is limited to 300psi. 1.0 ft Wo 4 ft 1.0 ft 0.75 in. 4 in. 0.75 in. 5 in. -0.75 in. -NA I= 46.7 in.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
The wooden beam shown is made by gluing together planks as shown. 8 kN/m Glue 80 mm A B 80 mm - NA 6 m 80 mm 160 mm Determine the maximum shear stress in the glue in kPa. (2 decimals)
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN. 0.8m 0.4m B 5KN 0.6m Al 20KN Q2 5) What is the deformation 8, in mm? A=800 mm? A=1,200 mm?
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)