Mechanics I need the answer asap thank you The four rigid gears, loaded as shown in the Figure, are attached to a hollow shaft. Compute the angle 9 of rotation of gear Arelative to gear D. Use G = 12 x106 psi for the shaft.poutside = 5 inpinside = 3 in600 lb ftD4 ft-1000 lb-ftRound your answer to 3 decimal places.GB18+/+38+/- 51f900 lb-ftC-5 ft-500 lb-ftAX

Answered: Image /qna-images/answer/69312cc0-4467-4832-8376-99d56d7c7cef.jpg

The four rigid gears, loaded as shown in the Figure, are attached to a hollow shaft. Compute the angle 8 of rotation of gear A relative to gear D. Use G = 12 x106 psi for the shaft. poutside = 5 in pinside = 3 in 600 lb-ft D 1000 lb ft 4 ft- 900 lb-ft C B 18-38+/- 5. ft - 5 ft- 1 500 lb ft A X

The four rigid gears, loaded as shown in the Figure, are attached to a hollow shaft. Compute the angle 8 of rotation of gear A relative to gear D. Use G = 12 x106 psi for the shaft. poutside = 5 in pinside = 3 in 600 lb-ft D 1000 lb ft 4 ft- 900 lb-ft C B 18-38+/- 5. ft - 5 ft- 1 500 lb ft A X

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A hollow aluminum shaft with an outside diameter of 80 mm and a wall thickness of 5 mm has an…

Q: the turning moment on the crank (in kNm)

A: Given, Crank rotating speed,N= 600 rpm Connecting rod length,L= 800 mm Crank radius,r= 200 mmCrank…

Q: A rigid strut ABCD supports two concentrated loads P at points B and D. It is being supported by a…

A: Given: The area of cable, A = 120 mm^2 = 120 x 10-6 m2 The elastic modulus of the cable, E = 50 GPa…

Q: Three guy wires with forces indicated in the figure are attached to an anchor bolt. Determine the…

A: To find : resultant force

Q: Technician A uses a micrometer to measure the connectingrod journal for taper. Technician B uses…

A: In this problem, it is asking that which technician is correct.

Q: The built-up shaft in figure consists of a pipe AB and a solid rod BC. The pipe has an inner…

A: Given : outer diameter of pipe AB, Do = 28 mm inner diameter of pipe AB, Di = 20 mm diameter of rod…

Q: 3. An oscillator is subject to an external driving force F(t), which is an exponentially decreasing…

Q: What is the smallest V-groove angle that can be weldedusing the FCA welding process?

A: Given Data : Smallest V-groove angle FCA welding process

Q: A cantilever truss shown is subjected to a wind load of 4.32 kN/m normal to the roof surface. Use $1…

A: given; load density(w)=4.32KN/mS1=0.8mS2=1.6mlets take compression force in FG member=Plets take…

Q: Find the forces in members EF, KL, and GL for the Fink truss shown. Forces are positive if in…

A: For the given truss, t is required to determine the forces in members EF, KL, and GL.

Q: The magnetic field surrounding the coil in a magneticpulse generator moves when the __ .a. Reluctor…

A: In this problem, it is saying that which one is correct when magnetic field surrounding the coil in…

Q: Compute the hydraulic radius Wetted area=22.5 m2 Wetted perimeter=14.5 m

A: Given data : Wetted area A=22.5 m2 Wetted perimeter P=14.5 m Required : Hydraulic radius

Q: 67. Which of these angles is adjusted last during a wheel alignment? a. Steering axis inclination c.…

A: " Since you have asked multiple questions we will solve the first question for you. If you want any…

Q: Find displacement Work done=1111 J Force=111 N

A: Given data: F=111 NW=1111 J Need to determine the displacement.

Q: 40° B C 20⁰ (0,0) 30⁰ Ä +y +X 3 forces are applied to a point. The magnitude of vector A is 10 N, B…

A: The vector sum of all the forces which are all acted in an object is said to be a net force. The net…

Q: A rectangular barge weighing 300,000 kg is 15 m long, 8 m wide and 5 Im deep. It will transport to…

Q: Discuss the difference between static and dynamic temperatures.

A: difference between static and dynamic temperature

Q: The provided S-N curve shows the fatigue strength of a ferrous component with unknown geometry.…

A: When a material is regularly cycled across a specified stress range, the number of cycles before…

Q: A thin rectangular plate is uniformly, deformed, as shown. Determine the shear strain γxyγx⁢y at P.…

A: Given data: a = 15 inb = 28 inc = 0.12 ind = 0.19 in Need to determine the shear strain at point P.

Q: A steam power plant operates on an ideal reheat Rankine cycle between the pressure limits of 15 MPa…

A: Given:P1=15 MPaP2=10 KPam=12 Kg/sT1=T3=500°Cx3=0.10

Q: Two masses, m and M, are connected by a spring whose force constant is k and slide freely on a…

A: given; two mass m &Mspring constant=knatura frequency of occilation(ω)=?

Q: In addition to continuously changing the weld pattern,what other changes must be continually made…

A: Considered to be the most challenging pipe position is the 66 or 45° fixed inclined position.…

Q: If the Poisson's ratio of an elastic material is 0.4, the ratio of modulus of rigidity to Young's…

A: Given, Poisson's ration of an elastic material = μ = 0.4 Modulus of rigidity (G), Young's modulus…

Q: If FB = 120 N and Fc = 140 N, a) Draw the Free-Body Diagram b) Determine the resultant moment about…

A: Given:FB=120 NFC=140 N

Q: Which of the following statements about drum brakeshoes is not true?a. Web thickness varies only…

A: Brake shoes are a major part of a drum brake system. these crescent-shaped components are made up of…

Q: Suppose you would like to introduce an interstitial or large substitutional atom into the crystal…

A: The illustration demonstrates that the dislocation is an edge dislocation. An edge dislocation is a…

Q: A ideal rankine power plant cycle uses ammonia as the working fluid. Saturated vapor leaves the…

A: Given:TH=85°CTL=40°C

Q: 500 N AY SOON Find the resultant system of converging forces in the figure. Below 200NX

Q: The drive shaft component that provides a means ofconnecting two or more shafts together is the __…

A: Various types of joints are used to join the shaft with each other to transmit power from one shaft…

Q: A 5 kW electric motor driving a pump has an efficiency of 85%. Determine the losses encountered in…

Q: A cold drawn 1144 Stressproof steel specimen with a diameter of 0.874 in. and a 1.0 in. gage length…

A: Given: The diameter of specimen, d = 0.874 in The length of the gage, L = 1.0 in

Q: Compute the hydraulic radius Wetted area=22.5 m2 Wetted perimeter=14.5 m

A: Given2 Wetted area A=22.5 m2 Wetted perimeter P=14.5m

Q: Why is a multicircuit evaporator used?

A: Multi circuit evaporator consists of two or more evaporator that can be at same temperature or at…

Q: Laboratory tests on a centrifugal pump, which is directly coupled to a motor running at constant…

Q: Consider the truos shown in (Egure 1). Suppose that Fi-60 kN and F-25kN Figure V 30 KN Part C 50 AN…

Q: An axial bar fixed at both ends with no loads applied is subjected to an increase of temperature.…

Q: 9.59. A 3 in. smooth pipeline 100 ft long carries 100 gpm of crude oil. Calculate the head loss when…

A: Given data: d=3 in=0.25 ftQ=100 gpm=0.2228 ft3/sL=100 ft Need to determine the head loss.

Q: Determine an expression for the power P, developed by a pump valve when P, depends upon H, discharge…

A: Given: P = Power (W) H = Head (m) Q = Discharge (m3/s) w = specific weight (N/m3) P = f (H,Q,w)

Q: For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A…

Q: For the shaft and gear system given below, assume that the shaft is supported at A and B with self-…

Q: Graphite is __.a. an anaerobic substanceb. an RTVc. an aerobic substanced. none of these

A: Graphite is a carbon compound and its crystal consists of layers of carbon atoms or sheets of carbon…

Q: A cubical reservoir(3.5mx3.5mx3.5m) is being filled with gasoline (SG=0.72) through section 1 with…

Q: Water at 25°C flows from a large reservoir to a smaller one through two clean cast iron pipes in…

Q: )draw the top view of the obeject b)from the top view draw a downward projection line for each…

Q: A square high-density polyethylene [a = 158x10-6/°C] plate has a width of 215 mm. A 129 mm diameter…

Q: A laboratory has a volume of 470 m3, and is to be maintained at 200C, 52.5% relative humidity. The…

A: Since you have posted a question with multiple subparts, we will solve first three sub parts for…

Q: List the advantages of having one ignition coil percylinder.

A: The timing at each cylinder may be adjusted independently, the saturation time and the interval…

Q: Determine the forces in members BC and CF of the loaded truss. Enter a positive number if in…

Q: The 16 x 22 x 25-mm rubber blocks shown in the figure are used in a double U shear mount to isolate…

Q: The maximum radial load it can sustain to

A: Given data, Bearing capacity of dynamic load of 4208 bearing is, F= 30 kNCalculate maximum radial…

Concept explainers

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.

Question

Mechanics

I need the answer asap thank you

The four rigid gears, loaded as shown in the Figure, are attached to a hollow shaft. Compute the angle 9 of rotation of gear A
relative to gear D. Use G = 12 x106 psi for the shaft.
poutside = 5 in
pinside = 3 in
600 lb ft
D
4 ft-
1000 lb-ft
Round your answer to 3 decimal places.
G
B
18+/+38+/- 51
f
900 lb-ft
C
-5 ft-
500 lb-ft
A
X

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The teeth of the gear arrangement have Gear A=40teeth, Gear B=70 teeth and Gear C= 50teeth, a pinion (driver Gear) that rotates at 625 rpm, and idler Gear B and a driven gear (Gear C). The gears have a module of 5mm and a pressure angle of 200. Find the pitch diameter of gear C in mm.
1. Two metric spur gears are engaged; the gear ratio is 3/2 and they have a module of 2.5 mm. Find the number of teeth for each gear if the center distance is 125 mm.
An epicyclic gear train as shown in figure. Gear D has 65 teeth, gear C has 15 teeth and annular gear A has 120 teeth. Gears B and C are compound. If the annual gear A is fixed and gear D rotate 600 rpm, find the speed of arm. A B- D -C
Two gears mounted on shafts have 10 and 15 teeth, respectively. The center distance is 10 inches. The addendum equals the module, and the clearance equals 0.135 times the module. Determine (a) pitch diameters, (b) addendum, (c) dedendum, and (d) root circles. Draw simple circles showing the diameters and the center distance. Complete solution and drawing is required.
A recurring gear train composed of four sprockets 2, 3, 4, 5, has a value of the train of 1: 4 ½, being all the teeth of the gears of the same pitch. 2 has 40 teeth, 3 has 60 teeth. Find the number of teeth in 4 and 5. If the diametral pitch is 3, find the distance between the centers of the arrows. Answer N4 = 25; N5 = 75; 16.667 in
There are three parallel shafts 1, 2 and 3. Gear A on shaft 1has 28 teeth of diametral pitch of 4 meshing with a larger gear B in shaft 2 having 70 teeth. A smaller gear C having 24 teeth on shaft 2 and diametral pitch of 5.2 meshes with a 50 teeth gear D of shaft 3. Determine the rpm of shaft 2 if shaft 1 turns 1,744 rpm.
The spur gear arrangement shown in Figure has a pinion (driver Gear A) that rotates at 700 rpm, an idler Gear B and a driven gear (Gear C). The gears have a module of 5 mm and a pressure angle of 20 degree. Given the number of teeth as shown, determine: The speed of Gear C NOTE: Write your answer in two(2) decimal places Example: 488.62 rpm 50 teeth A -90% B 80 teeth C 60 teeth
A bicycle's gear ratio is the number of times the freewheel turns for every one turn of the chainwheel (see figure). The back half of a bicycle is given. A line labeled "Freewheel" is pointing at the center of the rear wheel. A line labeled "Chainwheel" is pointing to the center piece connecting the two pedals. The table shows the numbers of teeth in the freewheel and the chainwheel for the first five gears of an 18-speed touring bicycle. The chainwheel completes one rotation for each gear. GearNumber Number ofTeeth inFreewheel Number ofTeeth inChainwheel 1 32 24 2 26 24 3 22 24 4 32 40 5 19 24 Find the angle through which the freewheel turns for each gear. Give your answers in both degrees and radians. (Round your answers to one decimal place.) gear 1 = rad= gear 2= ° rad= gear 3= ° rad= gear 4= ° rad= gear 5= ° rad=
Three spur gear are arranged shown in the figure. Pinion A rotates for about 500 rpm. The three gears have a diametral pitch of 5. Number of teath and angle is shown in the figure. Determine the torque that each shaft is required to transmit and the resultant force on the shaft carrying the gear B. Draw the FBD of the figure.
The axes of two parallel shafts are to be 600mm apart approximately, and have to be connected by spur gear, having a circular pitch of 30 mm. If gear A rotate at 200 rpm and gear B rotate at 600 rpm, find the number of teeth on each gear.
Gear 1 has a module of 2 and 26 teeth. This gear drives Gear 2 whose speed is 271.0 rpm. The shaft centre distance is 264 mm. What is the rotational speed (rpm) of Gear 1? Use 3 decimal places in your calculations. Supplementary Information Gears Formulae Diametral Pitch P = N/d module m = d/N p =nd/N=Tm WL-WArm e' Wf - WArm Product of the driving tooth numbers] 土 Product of the driven tooth numbers %3D Nr +1 N, Wsun Warm Standard Tooth Sizes and Systems for gears Diametral Pitch Coarse Fine Modules 2, 21/2, 21/2, 3, 4, 6, 8, 10, 12, 16 20, 24, 32, 40, 48, 64, 80, 96, 120, 150, 200 1, 1.25, 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10, 12, 16, 20, 25, 32, 40, 50 Preferred Next Choice 1.125, 1.375, 1.75, 2.25, 2.75, 3.5, 4.5, 5.5, 7, 9, 11. 14. 18. 22, 28, 36, 45 Dedendum b 1.25/Pa or 1.25m Addendum a Tooth System Full depth Pressure Angle Ø deg. 20 I/Pa or m 22v2 1/Pa or m 1.25/P or 1.25m 25 1/P or m 1.25/Pa or 1.25m Stub 20 0.8/P or 0.8m 1/P or m Answer: oロ C Search for anything
Two helical gears have shafts at 90° and a center distance of 364 mm. The speed ratio is 3:1 The smaller gear has 20 teeth; m, -6.5. Determine the values for the helix angles. Select one: O a. 53.4 and 42.2° O b. 47.8 and 33.2" O c. 47.8 and 42.2° Od 53.4 and 47.8°