The force F in the system shown has a magnitude of 500 N and angles directional a = 65°, B = 130° and y = 45°. Determine the moment produced by the force F around point O, if L1 = 0.4m, L2 = 0.3m and L3 = 0.5m. Express the result as a Cartesian Vector. L. L3 L2 F

The force F in the system shown has a magnitude of 500 N and angles directional a = 65°, B = 130° and y = 45°. Determine the moment produced by the force F around point O, if L1 = 0.4m, L2 = 0.3m and L3 = 0.5m. Express the result as a Cartesian Vector. L. L3 L2 F

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter2: Basic Operations With Force Systems

Section: Chapter Questions

Problem 2.46P: The force F=2i12j+5klb acts along the line AB. Recognizing that the moment of F about point B is...

See similar textbooks

Related questions

Q: A copper wire is stretched with a stress of 90 MPa (10,000 psi) at 30°C (68°F). If the length is hel...

Q: Q12 = 0A‚F,„(e¡T;* – a,T;')

A: A process in which heat waves are released and absorbed, reflected, or transferred through a col...

Q: What is the partial pressure (in atm) of the water vapor present in 1000 g of m air that contains 21...

Q: The car moves such that its speed uniformly increases with time from 50 kph at Position 0, to 80 kph...

A: Given data Velocity of car at position O = 50 kph = 13.89 m/sVelocity of car at position Q = 80 kph ...

Q: 'hy is it important when assessing indoor air quality to re arameters of the turbulence model as use...

A: introduction The structure gives asylum to live and most individuals invest their 85-90% energy insi...

Q: 100 mm 100 mm

A: GivenP=9kNd=6mm

Q: 3) Compute the centroid of the shaded area shown in figure Q.3

A: TO FIND centroid

Q: Air standard Otto cycle have 10 compression ratio, if specific heat at constant volume ( CV) increa...

A: An Otto cycle is a simplified thermodynamic cycle that describes how a spark-ignition piston engi...

Q: Q1) Find the values of the maximum tensile and compressive bending stresses for the simply supported...

A: Dear student, as per the guidelines of Bartleby we are authorized to answer the first question only....

Q: A solid shaft of diameter d and length L is fixed at both the ends. A torque, To is applied at a dis...

Q: 18. How many tons of refrigeration effect can be obtained from a window air conditioner rated at 18,...

A: Ton of refrigeration(TR) is the unit for heat removal Heat removal = Q = 18000 Btu/hr Find Ton of re...

Q: O N/m. l1=0.4 m and l2=0.6 m. A. Pump

A: data given Motor pump system Mass m =50 kg mass moment of inertia J0 =100 lg/m2 spring stiffness K...

Q: The value of the determinant in db - ca da- cb de + ba db + ca dc - ba.

A: Answer: ◆ The value of the determinant is (da - cb). ◆ Therefore, the correct answer is option (b). ...

Q: A mass of 18 kg is attached to two identical springs each with stiffness 7OKN/m under friction less ...

Q: 3.5 Construct IPR of a well in a saturated oil reservoir using both Vogel's equation and Fetkovich's...

Q: A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling sy...

Q: 8.4 A material is subjected to two mutually perpendicular stresses, one 60 MN/m compressive and the ...

Q: 1. Draw a sound conclusion based on how you familiarized the key components of the surface grinding ...

Q: What is the problem arise when design a pneumatics system with more than 1 cylinder and What are the...

A: the problem arises when designing a pneumatics system with more than 1 cylinder Because some pneumat...

Q: A bearing piece in the form of half of a hollow cylinder of 60 mm ID, 90 mm OD and 100 mm long is to...

Q: A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling sy...

A: Write the given data. Q=400 gal/min

Q: A mechanism is composed of the following • Link 1 (AF) - horizontal ground with a length of 7 cm. "A...

A: Given : Link 2 rotated counterclockwise To find : Velocity of Link C and E

Q: After some engine model replacement, an aircraft model is experiencing some aggressive nose up pheno...

Q: The polyethylene sheet is subjected to the biaxial loading shown. Determine the resulting elongation...

A: Answer: (a) The elongation of side AB is 0.3648 inches. (b) The elongation of side AC is 0.0640 inch...

Q: 2. Find the view factors for this configuration. a. Fis b. Fia c. F12 0.25m -0.1m

A: (a) Consider the circle and write the expression for view factors. R51+R52+R53+R54+R55=1

Q: . Find the width of the belt used it

A: To find width of belt (b)

Q: Q1// A heat engine receives 1000 KJ of thermal energy from a heat source. (60%) of the resulting wor...

Q: Use the von Mises failure criterion to solve for the minimum required yield stress if a factor of sa...

Q: Consider the water flowing through the transition shown. If the difference in the level of mercury w...

A: As per given H=64mm Diameter D1=0.1m and D2=0.04m ρHg = 13 550 kg/m3 We have to determine volumes...

Q: . Determine the Saturation Temperature and Saturation Pressure of the following

A: Determine the saturation temperature and saturation pressure.

Q: An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air i...

Q: F F F A C В If F = 50KN, AC = 2 m, BC = 5 m, then find moment at point B. %3D

Q: Read the questions carefully and answer with complete solution and units.Use the steam tables provid...

Q: A steam power plant operates on the ideal Rankine cycle producing a net power output of 120 MW. The ...

A: Answer: ◆ The quality of steam entering the condenser is 74.10%. ◆ Qa = 3155.71 kJ/kg , Qr = 1795.96...

Q: A 64-lb weight suspended from a spring (spring constant is 200 lb/ft) is released from rest 0.4 ft b...

Q: Find the brake power of the engine running at 755 rpm. The iength of lever from centre of pulley is ...

A: We need to figure out how much braking power the engine has at 755 rpm.The lever is 1.43 metres long...

Q: [4/ (2x + 5)] = [? / (2x² – x - 15)]

Q: Q1// A heat engine receives 1000 KJ of thermal energy from a heat source. (60%) of the resulting wor...

Q: (a) Explain the steps involved in representing the natural a flows within a building using the nodal...

A: Natural and mechanically driven air flows The paper portrays a displaying investigation of hotness m...

Q: EXPLAIN THE GENRAL TIPS OR GUIDELINES FOR A SAFE WORKSHOP

A: Workshop Guidelines and Safety precautions :

Q: Find the brake power of the engine running at 755 rpm. The length of lever from centre of pulley is ...

Q: 2. x(t) = sin2t (e5t) y(t) = D³ + 3D² +3D1 +1 Determine: a) Laplace Transform of x(t) b) Laplace Tra...

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for...

Q: a. A gear of 80 teeth and a pinion of 20 teeth has a gear and pinion ratio of 4. Find the tooth thic...

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked . K...

Q: Connecting rod ABC, ahown below, moves along the confined paths atCand at B. At the instance shown, ...

Q: Water flows out of a faucet at A at VA = 5.3 m/s.Determine the velocity of the water just before it ...

Q: a capsule attached to a line is being rotated in a vertical loop of radius of 15 meters determine: ...

A: Given: r = 15 m and vertical circular motion

Q: A duct 0.40 m high and 0.80 m wide suspended from the ceiling in a corridor, makes a right angle tur...

A: Given data as per the question The inner radius = 0.2 m outer radius = 1.0 m The velocity of air in ...

Q: Use the method of members to find the components of the forces acting on the frame with P=750N and Q...

Q: A 1500 kg load is lifted by a hoist using a Ø1.5 m drum. The drum is driven by an electric motor.thr...

Q: Q1. Collar A moves at a velocity, V4, to the right. The values of the kinematic parameters are given...

Question

The force F in the system shown has a magnitude of
500 N and angles
directional a = 65°, B = 130° and y = 45°. Determine
the moment produced by the force F around point O,
if L1 = 0.4m, L2 = 0.3m and L3 = 0.5m. Express the
result as a Cartesian Vector.
Li
L3
Lz
F

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The force F=2i12j+5klb acts along the line AB. Recognizing that the moment of F about point B is zero, determine the x- and z-coordinates of point B.
Find the resultant force vector,R, of the three vectors A,B, and C (i.e., add the vectors), if the magnitude of vector A is 10N, the magnitude of vector B is 17N, and the magnitude of vector C is 9N. Your answer should be in the form R = Rx i+ Ry j, where you determine Rx and Ry, and where i, and j are the unit vectors along the x, and y axis, respectively. YA В A 60° 45°
A force acting through the point (X, Y, Z) where X = 4, y = -3 and Z = 8 is given by the vector: F = ai + bj + ck where a = 7, b = 4, c = -4 Determine the magnitude of the moment produced by F about the point (1,2,3). Give your result to three decimal places.
Q3- Determine the moment of the force about point O. The Force Has A Magnitude Of 800 N And Coordinate Direction Angles Of a = 60°, B = 120° 45°. Express The Result As A Cartesian Vector. » Y = 80 Nm 30 0.4 m -0.5 m. 0.3 m 40 Nm A F
9. Express the force F= 1200 N in Cartesian vector form. 4 m m F = 900 N 2 m B 2m
Q3- Determine the moment of the force about point O. The Force Has A Magnitude Of 800 N And Coordinate Direction Angles Of a = 60°, ß = 120°, y = 45°. Express The Result As A Cartesian Vector. %3D 80 Nm 30 0.4 m -0.5 m- 0.3 m 40 Nm F
Determine the x- and y-coordinates of a point through which the resultant of the parallel forces passes. y 20 lb 90 lb 85 lb 30 Ib 16" 7" 13" 13" 25 lb v Part 1 The problem asks us to replace these five forces with a single equivalent force. The new system is shown below. y Find the force R. Answer: R = Ib
2. A cleat on a boat is used to support forces from three ropes as shown. Determine the resultant force vector R, using Cartesian representation, and determine the magnitude R. Also, express R in polar vector representation. F2 = 200 N F1 = 400 N 40° F3 = 100 N 12 30°
Q6- Two forces F1=240 lb and F2=160lb act on the hip joint. Determine the resultant of the two forces and express the result as a cartesian vector. Also, find the coordinate direction angles of the resultant force. Z F1= 240 lb 75° 131 F2 = 160 lb ww 45° y
SOLVE ASAPThe line of action of force F₁ = 388 N is passing through point A(+2,+3,+1) towards B(+5,+5, +4), while that of force F₂ = 488 N is through point C(+3,+1,−1) towards D(-2, -3, -4). Use a right-handed coordinate system.a. Determine the moment of force F₁ about the origin.b. Determine the moment of force F2 about the origin. c. Determine the magnitude of the resultant moment of forces Fi and F₂ about segment OE. Point O is the origin and point E is at (+5,+5,-3).
B- Use the graphical method to find the magnitude and direction of the resultant of these forces. y 60° 30 F = 700 N 45 F, = 500 N
Find the magnitude and direction of the resultant force if F1 = 60 N at 45 deg N of W and F2 = 50 N at 60 deg S of E.