The following shows the top view of the partially open doors on one side of an entertainment center cabinet. The wooden doors are hinged to each other and one door is hinged to the cabinet. There is also a ternary, metal link attached to the cabinet and door through pin joints. As spring- loaded piston-in-cylinder device attaches to the ternary link and the cabinet through pin joints. Draw a kinematic diagram of the door system and find the mobility of this mechanism. cylinder cabinet link hinge door door hinge

The following shows the top view of the partially open doors on one side of an entertainment center cabinet. The wooden doors are hinged to each other and one door is hinged to the cabinet. There is also a ternary, metal link attached to the cabinet and door through pin joints. As spring- loaded piston-in-cylinder device attaches to the ternary link and the cabinet through pin joints. Draw a kinematic diagram of the door system and find the mobility of this mechanism. cylinder cabinet link hinge door door hinge

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Inclined plane diagram: Also String 1 String 2 String 1 B C A The diagram above shows Carts B and C which roll without friction over an inclined plane. The plane is inclined at an angle of theta = 0 away from vertical, as shown in the diagram. Carts B and C are connected by an essentially massless string. Another massless string runs from Cart B over a massless and frictionless pulley to a hanging block, Block A.
Draw the kinematic diagram of the given mechanism and identify it's mobility by determining it's degree/s of freedom in the space provided (input a NUMERICAL value). The end of the handle should be identified as a point of interest. Make sure to include the drawn kinematic diagram in the solutions that will be uploaded at the end of the assessment. DEGREE/s OF FREEDOM =
Identify whether the following set of dimensions determines a Grashoff, Non-Grashoff or Special Case mechanism. If it is a Grashoff mechanism state what is kind of kinematic inversion it is (ex. Crank-Rocker, etc.). Provide necessary computations
Identify whether the following set of dimensions determines a Grashoff, Non-Grashoff or SpecialCase mechanism. If it is a Grashoff mechanism state what is kind of kinematic inversion it is
For the following figure, draw a kinematic diagram for each identifyingthe point of interest. From there, calculate the mobility of the device.
Given the two-link planar arm with rotary joints below. For this arm, the second link is half as long as the first–that is, L1 = 2L2. The joint range limits in degrees are: 0 < 0, < 180, -90 < 02 < 180. L1 Sketch the approximate reachable workspace (an area) of the tip of link 2.
1. Find a combination of link lengths where motion of a point on output link is one quarter of a circle. 2. Find the value of all 0, 0, 0, and y in open and close configuration Read the value of link lengths and the input angle 8., then use the formulae given below to calculate the value of unknowns 03, 0, and y K₁ = = K₂= d K2 K3 = a²-b²+c²+d² 2ac A = cos 0₂ - K₁ - K₂ cos 0₂ + K3 B = -2 sin 0₂ C = K₁ (K₂ + 1) cos 02 + K3 -B± √B²-4AC 2A 0412 = 2tan-1 d K₁ = — K5 = c²d²a²-6² 2ab D = cos 0₂ - K₁ - K4 cos 0₂ + K5 E = -2 sin 0₂ FK₁+ (K₁ - 1) cos 02 +K5 0312 2 tan-1 (-E± -E± √E²4DF 2D Y = 04-03
Slide B travels along the center line XX'. Q2A = 18 cm, AB = 72 cm. 1. With the crank in the position shown, draw the four bar linkage. Name each link and show the finite and infinite cranks.2. Find the two extreme positions of block B. Express your answer in terms of the acute angle formed by crank Q2A with the horizontal axis (like the angle 45° in the figure)3. Determine the length of the stroke of B. Write your answer in two decimal places.
Determine a body or system of your own to analyze statically using concept from this class! Requirements: • Draw a static system (either in 2D or 3D). For instance, I may draw a clothes drying rack in 3D. See below for a visual of the clothes drying rack. ● In this drawing prescribe a force or moment at some point on the body. For instance, I may prescribe a force at the top of the drying rack simulating a shirt hanging from the rack. Explain the concepts you would use to figure out an applicable force/moment at another point/member while the body is in equilibrium. For instance, I would use a combination of concepts of FBD/equilibrium and method of joints/sections to find the internal member forces of each drying rack member. 5
Attached is the image of the system, as well as the question. The equations are my derivations from the system. Please answer letters a-e at the bottom
Topic: Grashof's Law - Four Bar Linkage MechanismWhat are the different links and how to identify which is which?Please watch this video for reference: https://www.youtube.com/watch?v=h8bz4ni6mdY&t=145s
1–2. Figure C1.2 shows a mechanism that is typical in the tank of a water closet. Note that flapper C is hollow and filled with trapped air. Carefully examine the configuration of the components in the mechanism. Then answer the following leading questions to gain insight into the operation of the mechanism. 1. As the handle A is rotated counterclockwise, what is the motion of flapper C? 2. When flapper C is raised, what effect is seen? 3. When flapper C is lifted, it tends to remain in an upward position for a period of time. What causes this tendency to keep the flapper lifted? 4. When will this tendency (to keep flapper C lifted) cease Plz connect me if you want to explan subject for me .... +962 79180149 Thx