The following data was collected in a FUEL CELL reaction (not Electrolysis reaction):Time1 second270 secondsE (volts)100%90%80%70%0.9800.9970.939 (average)(amps)0.1240.1140.119 (average)Calculate the Faraday Efficiency of the Fuel Cell reaction.H2 (ml)6 (starting vol)1 (remaining vol)5 (consumed)

Average current (I) = 0.119 amperesTime duration(t) = 270 secNow, one mole of hydrogen (H2) would…

The following data was collected in a FUEL CELL reaction (not Electrolysis reaction): Time 1 second E (volts) 0.980 270 seconds 0.997 100% 90% 80% 70% 0.939 (average) (amps) 0.124 0.114 0.119 (average) Calculate the Faraday Efficiency of the Fuel Cell reaction. H2 (ml) 6 (starting vol) 1 (remaining vol) 5 (consumed)

The following data was collected in a FUEL CELL reaction (not Electrolysis reaction): Time 1 second E (volts) 0.980 270 seconds 0.997 100% 90% 80% 70% 0.939 (average) (amps) 0.124 0.114 0.119 (average) Calculate the Faraday Efficiency of the Fuel Cell reaction. H2 (ml) 6 (starting vol) 1 (remaining vol) 5 (consumed)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If fuel is combusted with Oxygen instead of air and have full combustion reaction, the adiabatic flame temperature will be higher than it with combustion with air True False If we richening the combustion then hydrogen concentration increases in the exhaust gases of the tailpipe True False
The following gravimetric analysis on an ash and moisture free basis of a kilogram of Fuel oil are the following: C=87%; H=12%; N=2%, S=2%; and O=6%. The yields on the burning of the same fuel are in the following Orsat Analysis: C02=11%; CO=2%; 02=4.5%; and N2=82.5%. 1) Calculate the mass of dry flue gas in kilogram.2) Determine the mass of the ideal air in kilogram of air. 3) Determine the percent of excess air.
A) A natural gas-fired industrial boiler operates with an oxygen concentration of 3 mole percent. Determine the operating air-fuel ratio and the equivalence ratio. Treat the natural gas as butane B) Write the equation of pentane-air combustion and determine the stoichiometric air-fuel ratio
Part 1:Design a three-component gasoline blend. Specify the boiling temperature of your blend.Additionally, determine the Research Octane Number (RON), Motor Octane Number (MON), andAnti-Knock Index (AKI) for this blend. Lastly, evaluate whether this fuel is sensitive to combustionchamber geometry.Part 2:Hydrogen is utilized as a fuel in an experimental engine and is combusted with stoichiometricoxygen. Assume the reactants initiate at a temperature of 25°C. Write the balanced chemicalreaction equation for this combustion.Perform the following calculations:(a) Determine the fuel-air (fuel-oxygen) ratio.(b) Calculate the equivalence ratio for the combustion process.
4.1 fuel-rich air-fuel the exhaust gives the following 14.957; Cullg = 0.75% 0% H₂ = 0% 0₂ = 0%, with the rest being N₂. Write the balance chemical equation for one mole of this fuel at these conditions. CO = 1 Calculate : CHHS is burned in an engine with a ratio. Dry analysis of volume percents CO₂ : a- Air-fuel ratio. b. Equivalence ratio.
A Methanol pool fire shows a fuel mass loss rate of 0.01 kg/s on a load cell Estimate the heat release rate Assume a combustion efficiency of 08 The heat of combustion of Methanol can be obtained from the text book (Table 76) O A 160 KW O B. 20000 KW OC. 200 kW O D. 16000 kW QUESTION 2 Estimate the heat release rate for a keroene pool fires with a mass loss rate of 0 123 kg/s Assume combustion officiency 08 O A. 2000 KW O B. 200 kW OC 4250 kW OD. 34500 KW QUESTION 3 If the diameter of the kerosene pool fire from the above question (Question 2) is2 m, estimate the flame hoight of the pool fire. O A.04 m OB.4 46 m OCB0M O D. 42m
5. A test run using this coal showed a dry products of combustion analysis by volume of nitrogen equals 82.5%, molecular weight of 30 kg flue gas per mol dry flue gas, and the weight of this dry flue gas is 15.03 kg per kg of coal. The actual ash-pit sample was 0.15 kg per kg of coal, of which 20% was carbon. What is the percentage excess air supplied to the fuel combustion in percent?
QUESTION 8 (Fuels and Combustion) A boiler is fired with a fuel having a mass composition: C = 86.1%, H2 = 3.9%, O2 = 1.4% and ash = 8.6%. Volumetric analysis of dry flue gases gives CO2 = 12.7%, CO = 1.4%, O2 = 4.1% and N2 = 81.8%. Calculate: (a) The total amount of flue gas per kg of fuel fired. (b) The percentage of excess air supplied above the minimum quantity required for complete combustion of fuel.
QUESTION 6 (Fuels and Combustion) The chemical analysis by mass of a fuel is: C = 87.1%, H2 = 4.4%, O2 = 1.2% and ash = 7.3%. Determine the amount of air required for combustion of the fuel.
ANSWER THIS THERMOFLUID QUESTIONS
Problem 4) LHV and HHV of Fuels Consider the following list of some fuels with their LHV and HHV. a) Provide a plot of the LHV as a function of the molecular mass of the fuel. Group the fuels in categories and discuss any correlation between the heating values and the molecular mass. b) Provide a plot of the percentage increase of the HHV relative to the LHV as a function of the molecular mass of the fuel. Discuss any correlation or generalization. Fuel LHV and HHV LHV Methane (CH4) Propane (C3H8) Isooctane (C8H18) Cetane (C16H34) Methanol (CH40) Ethanol (C2H60) Carbon Monoxide (CO) (MJ/kg) 50.0 46.4 44.2 44.0 20.0 26.9 10.1 HHV (MJ/kg) 55.5 50.4 47.8 47.3 22.7 29.7 10.1
Why is heat usually the last thing determined when using a PV diagram?