The figure shows the excitation curve (including residual voltage) of a 170 kW, 250 V DC shunt generator at rated speed of 850 rpm. The generator has negligible (0 W) armature resistance and a shunt field coil resistance of 50 W. The variable Field Control Rheostat in series with the shunt field coil has variable resistance in the range of 0 – 25 W. Explain your reasoning for choosing the following answer. What is the rheostat resistance settings when the induced voltage is 300 V and the generator is turning at 120% rated speed? 12.65 Ω 10.47 Ω 8.32 Ω 3.25 Ω 2.22 Ω

The figure shows the excitation curve (including residual voltage) of a 170 kW, 250 V DC shunt generator at rated speed of 850 rpm. The generator has negligible (0 W) armature resistance and a shunt field coil resistance of 50 W. The variable Field Control Rheostat in series with the shunt field coil has variable resistance in the range of 0 – 25 W. Explain your reasoning for choosing the following answer. What is the rheostat resistance settings when the induced voltage is 300 V and the generator is turning at 120% rated speed? 12.65 Ω 10.47 Ω 8.32 Ω 3.25 Ω 2.22 Ω

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

The excitation circuit of a free-excited DC motor is a single-phase full- wave uncontrolled rectifier and The armature circuit is fed with a single-phase full-wave controlled rectifier. both rectifiers for AC voltage voltage 220 V(rms) ,is 50 Hz. Excitation O resistance of motor Rf = 100, armature force resistance Ra = 2 0 and motor voltage constant Kv = 0.25 V/(A - r/s). The motor is a fixed 10Nm buy under load a) Draw the driver (converter-motor) power circuit. To rotate with 1200 d/d of the motor, b) Calculate the thyristor assembly. c) When the engine is heavily loaded, with a suitable probability value for supply voltage, armature voltage, armature flow wavelengths draw below. d) Calculate the motor power (total input power). (Note: Va = IaRa + ea, Vf = IfRf, ea = Kv Ifw and Te = Kv Ifla)
What is use of solenoid coil in the pressure to converter? a. To produce magnetic field in the LVDT b. To change the LVDT output c. To bring back the pivoted beam normal position d. To produce linear displacement in bellows
Self-Lift P/O Luo- Dc-dc Converter i need explain Drive for seperately excited dc motor
Draw dc load line :
The single - phase ac voltage controller with inductive load. Plot the waveform of output voltage and voltage in each thyristor if the B = 10 %3D degree and delay angle (alpha) in both thyristor is 1- (30 degrees) 2- (90 degrees) 3- (120 degrees)
Speed control of a 140 V, 1.68 kW DC motor single phase thyristor full wave AC-DC It is made by the converter. AA supply voltage 220 V (rms) Is 50. In the converter It is assumed that there is no loss. The armature resistance of the DC motor is = 0.417 Q. Very a large inductance is connected in series with the motor. The motor voltage constant is = 0.0964 V/rpm. The motor can be considered as a permanent magnet DC. According to this, a) Draw the driver (converter-motor) power circuit. b) Calculate the nominal current of the motor. c) Supply voltage, supply current, converter output voltage for ignition angle a = 30 ° and Draw the waveforms for the converter output current. d) = 950 rpm and for nominal current, d1) The firing angle of the converter, d2) Effective value of supply and thyristor current, d3) Supply power factor, calculate.
Untitled Section Jalis 6 In d.c. generators armature reaction is produced by field current O armature current commutating winding current none of the mentioned compensating winding current *.The use of d.c. generators eliminated the use of rectifiers and ac supplies True False O
Question 2. Considering this figure. The firing angle is 45°, the motor current is 10 A, and the supply voltage is 110 v. 0₁ 0₂ 90 (a) Draw the waveforms of v, Vo. io. isi, iDi, and i. (b) Determine the power taken by the dc motor. (c) Determine the supply volt-amperes and supply power factor. Assume that the converter is lossless. (d) Determine the rms value of the SCR current and the diode current.
help me in these questions pls write the questions with the and by (Computer) 1-Which of the following statements INCORRECTLY explain the label in the figure about LVDT working principles? a. Secondary coils are connected in series in such a way that their output is opposing each other. b. Constant DC voltage input to primary coil. c. Displacement moves ferrous rod from central position. d. The difference of the output voltage between the two secondary voltage.==========2- Explain the working principle of the measurement system in the figure below.i. Force input that is supplied to the sensor is processed to give the response in the form of raw output signal.ii. Signal conditioner manipulated the weak signal to give a conditioned input.iii. Analog or digital indicator display the unit that gives output reading of quantity being measured.iv. Measured value is compared with the input value for further action. a. ii, iii and iv only. b. i, ii and iv only. c. i, ii and…
Q3 Draw the equivalent circuit of a DC Motor, Separated Excited DC Motor and Compounded DC Motor. Label each component properly (a)
h) Explain the methods of voltage control used in AC-AC converters.
Design a LabVIEW program that sweep Servo motor from 0 degrees to the specified angle and repeat Design a LabVIEW program to demonstrate a 28BYJ-48 stepper motor operating in both directions: 5 seconds anticlockwise and 5 seconds clockwise