The figure shows an RLC circuit. Vin is a sinusoidal voltage source that is 2 V in amplitude. Vin (2 sine ww 400 Ω 25 nF 150 mH (a) Determine the resonant frequency fo of the circuit. (b) Find the magnitude and phase of the current at a frequency of 5 kHz. (c) What is the quality factor Q for this circuit?

The figure shows an RLC circuit. Vin is a sinusoidal voltage source that is 2 V in amplitude. Vin (2 sine ww 400 Ω 25 nF 150 mH (a) Determine the resonant frequency fo of the circuit. (b) Find the magnitude and phase of the current at a frequency of 5 kHz. (c) What is the quality factor Q for this circuit?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 1PA: You are an electrician working in a plant. A series resonant circuit is to be used to produce a high...

See similar textbooks

Similar questions

Identify the reason for a nonsinusoidal signal being distorted when it passes through a filter. -The distortion occurs because harmonics are removed or rejected, leaving a different waveshape. -The distortion occurs because harmonics are synchronized, leaving a different waveshape. -The distortion occurs because the signal is modulated, leaving a different waveshape. -The distortion occurs because harmonics are added in the filter, leaving a different waveshape.
H.W: A resistor of resistance R-1000 2 is maintained at 17 °C and it shunted by 100 uH inductor. Determine the rms noise voltage across the inductor over a frequency bandwidth of: i) 15.9 kHz Ans: 182 x109 volt ii) iii) Ans: 9.22 x10-8 volt Ans: 2.34 x10-6 volt 159 kHz 1590 kHz
a. Determine the frequency responseVout( jω)/Vin( jω) for the circuit of Figure. b. Plot the magnitude and phase of the circuit forfrequencies between 10 and 107 rad/s on graphpaper, with a linear scale for frequency. c. Repeat part b, using semilog paper. (Place thefrequency on the logarithmic axis.) d. Plot the magnitude response on semilog paper withmagnitude in decibels.
A parallel R-L-C circuit is fed by a constant current source of variable frequency. The circuit resonates at 100 kHz and the Q-factor measured at this frequency is 5. Find the frequencies at which the amplitude of the voltage across the circuit falls to (a) 70.7% (b) 50% of the resonant frequency amplitude.
In a series RLC circuit, the applied voltage is 120V. At resonance, the frequency is 200rad/sec, and the circuit current is 6.26 A. What is the resistance of the circuit (in Ohms)? (Use 2 decimal places. Unit is not required.)
Ex: Design a noninverting summer circuit to achieve a 3 summing function for two analog signals 3 filt) = 5 Sin 2πT 10³t and f(t) = Ult). Draw the output waveform.
Show the capacitors, whether it is effective at low or high frequencsies Draw low frequency small-signal-equivalent circuit. AND LOWER corner is 82Hz frequency. Design the circuit. Draw the high frequency small-signal-equivalent circuit. AND UP-CORNER İS 172Hz frequency. DESİGN THE CIRCUIT.
Find DFT values of x-[6 87 4] and plot amplitude and phase spectrum. Write axis labels.
In a series RLC circuit, the applied voltage is 108V. At resonance, the frequency is 200rad/sec, and the circuit current is 8.38 A. What is the resistance of the circuit (in Ohms)?
IN A SERIES RLC CIRCUIT DRIVEN BY SINUSOIDAL INPUT SIGNAL, THE PHASE BETWEEN THE CURRENT AND THE INPUT VOLTAGE IS PLOTTED IN THE NEXT GRAPHAT FREQUENCY OF THE DRIVING (INPUT) VOLTAGE F= 1OKHZ THE PHASE BETWEEN THE CURRENT AND THE INPUT VOLTAGE IN RADIANS IS ABOUT: 1.6 1.2 0.8 0.4 -0.4 -0.8 -1.2 -1.6 1 10 100 1000 Frequency (f), kHz O g. 0.8 O b. 0.4 O c. 1.57 O d. 3.2 O e. zero pe. (0) aseyd
what is the phase angle of iT in degrees when expressed as a cosine function?
What is the difference between frequency modulation and phase modulation? DO NOT COPY FROM THE BOOk, please write it in your own words.