The figure below shows an AC source, a transformer with a turns ratio of N₁/N₂ = 2.70, a source resistor Rs, and R₂ ΔV, eeeee N₂ R₁ load resistor R₁. Ⓡ A voltmeter across the load resistor measures an rms voltage of 26.0 V when the load resistor R₁ is 48.00 and the rms source voltage is AVS = 86.0 V. (a) Determine the value of the source resistor R, (in (2). x How is the rms voltage across the secondary coil related to that of the primary? How is the power delivered to the primary related to the power delivered to the load resistor? How are the voltages across each element on the primary side related to each other? (b) What If? If the turns ratio is increased to 3.00, determine the source resistance (in 2) required to deliver the same amount of power to the load. How can you modify your work from part (a) in order to determine the source resistance required to deliver the same amount of power to the load resistor as in part (a)? Q

The figure below shows an AC source, a transformer with a turns ratio of N₁/N₂ = 2.70, a source resistor Rs, and R₂ ΔV, eeeee N₂ R₁ load resistor R₁. Ⓡ A voltmeter across the load resistor measures an rms voltage of 26.0 V when the load resistor R₁ is 48.00 and the rms source voltage is AVS = 86.0 V. (a) Determine the value of the source resistor R, (in (2). x How is the rms voltage across the secondary coil related to that of the primary? How is the power delivered to the primary related to the power delivered to the load resistor? How are the voltages across each element on the primary side related to each other? (b) What If? If the turns ratio is increased to 3.00, determine the source resistance (in 2) required to deliver the same amount of power to the load. How can you modify your work from part (a) in order to determine the source resistance required to deliver the same amount of power to the load resistor as in part (a)? Q

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter33: Inductors And Ac Circuits

Section: Chapter Questions

Problem 76PQ: In a series RLC circuit with a maximum current of 0.250 A, an AC source with Vmax= 115 V operating...

See similar textbooks

Similar questions

An RLC series circuit consists of a 50 resistor, a 200F capacitor, and a 120-mN inductor whose coil has a resistance of 20. The source for the circuit has an tins emf of 240 V at a frequency of 60 Hz. Calculate the tins voltages across the (a) resistor, (b) capacitor, and (c) inductor.
In a series RLC circuit with a maximum current of 0.250 A, an AC source with Vmax= 115 V operating at 60.0 Hz is connected to a 325-mH inductor, a 7.50-F capacitor, and a resistor with unknown resistance R. Draw a phasor diagram for this circuit, including the current, the potential difference across each of the circuit elements, and the source emf. Draw your diagram with the current phasor pointing upward along the vertical axis.
A 40-mH inductor is connected to a 60-Hz AC source whose voltage amplitude is 50 V. If an AC voltmeter is placed across the inductor, what does it read?
An ac source of voltage amplitude 10 V delivers electric energy at a rate of 0.80 W when its current output is 2.5 A. What is the phase angle between the emf and the current?
The emf of an ac source is given by v(t)=V0sint, where V0=100V and =200 . Find an expression that represents the output current of the source if it is connected across (a) a 20-pF capacitor, (b) a 20-mH inductor, and (c) a 50 resistor.
In a purely inductive AC circuit as shown in Figure P21.15, Vmax = 100. V. (a) The maximum current is 7.50 A at 50.0 Hz. Calculate the inductance L. (b) At what angular frequency is the maximum current 2.50A? Figure p21.15
A 20-mH inductor is connected across an AC source with a variable frequency and a constant-voltage amplitude of 9.0 V. (a) Determine the reactance of the circuit and the maximum current through the inductor when the frequency Is set at 20 kHz. (b) Do the same calculations for a frequency of 60 Hz.
A step-up transformer is designed so that the output of its secondary winding is 2000 V(rms) when the primary winding is connected to a 110-V (rms) line voltage, (a) If there are 100 turns in the primary winding, how many turns are there in the secondary winding? (b) If a resistor connected across the secondary winding draws an rms current of 0.75 A. what is the current in die primary winding?
A series RLC circuit has resistance R = 50.0 and inductance L. = 0.500 H. (a) Find the circuits capacitance C if the voltage source operates at a frequency of f = 60.0 Hz and the impedance is Z = R = 50.0 . (b) What is the phase angle between the current and the voltage?
The emf of an ac source is given by v(t)=v0sint. where V0=100V and at =200rad/s . Calculate the average power output of the source if it is connected across (a) a 20F capacitor, (b) a 20-mH inductor, and (c) a 50 resistor.
In an oscillating RLC circuit, R = 7.0 L. = 10 mH. And C = 3.0 F. Initially, the capacitor has a charge of 8.0 C and the current is zero. Calculate the charge on the capacitor (a) five cycles later and (b) 50 cycles later.
A series RLC circuit has resistance R = 50.0 and inductance L. = 0.500 H. (a) Find the circuits capacitance C if the voltage source operates at a frequency of f = 60.0 Hz and the impedance is Z = R = 50.0 . (b) What is the phase angle between the current and the voltage?