The compound DC generator shown below is rated at a terminal voltage of 100V when delivering rated load. In the diagram below it is delivering its rated load (6HP). Stray losses are 250W. Fill in the blanks below: R₁ = 0.18 IL e) f) Load Current= Shunt Field Current= Armature Current= Generated voltage Eg= Copper Losses= Efficiency= Amps Amps Amps Volts Watts % ele = 120 ₁= R₂=5 E. 6 HP

The compound DC generator shown below is rated at a terminal voltage of 100V when delivering rated load. In the diagram below it is delivering its rated load (6HP). Stray losses are 250W. Fill in the blanks below: R₁ = 0.18 IL e) f) Load Current= Shunt Field Current= Armature Current= Generated voltage Eg= Copper Losses= Efficiency= Amps Amps Amps Volts Watts % ele = 120 ₁= R₂=5 E. 6 HP

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The terminal voltage of a 150 kW series generator is 600 V at rated load. The armature resistance is 0.06 ohms and the series field resistance is 0.04 ohms. Find generated emf.
A long shunt compound generator delivers a current of 10A at 200V and has a series field resistance and shunt field resistance of 1 ohm and 200 ohms respectively. Then line current is a. 2A b. 1A c. 9A d. 10A
An 135-pole d.c. shunt generator with wave wound armature having 620 conductors, has to supply a load of 170 lamps each of 135W at 235 v. The flux per pole is 22 mWb and Ra = 2 ohms, Rsh=70ohms. What will be the load current and e.m.f generated. Consider brush drop of 1.6v/brush. Load Current Generated EMF In DC generators brushes are used for
. Two dc shunt generators A and B are rated at 100 and 150 kW at 110 V respectively, Their external load characteristics may be considered as straight line. The voltage drop In the terminal voltage from no-load to full-load Is 10 V for A and 20 V ſor B. Determine the operating voltage when these generators are operated in parallel to supply a load of 220 kW.
An 135-pole d.c. shunt generator with wave wound armature having 620 conductors, has to supply a load of 170 lamps each of 135W at 235 v. The flux per pole is 22 mWb and Ra = 2 ohms, Rsh=70ohms. What will be the load current and e.m.f generated. Consider brush drop of 1.6v/brush. Load Current Generated EME
A P=15 Kw a shunt generator with load voltage is 300V and resistace of the shunt field and armature are 50 and 0.5 ohms respectively. Calculate the generated emf.
A 6 pole wave wound d.c. shunt generator has 500 conductors. A generator delivers 50 kW of power at 250 voltage at full load. The resistance of the field circuit is 125 2. Actual brush shift is 10°. Then find the demagnetizing and cross magnetizing ampere turns per pole and how many additional turns must be wound on each pole to eliminate the demagnetizing effect.
The parallel operator of two dc generators will share the load current equally when: A. EA = EB and raA = raB. %3D B. PrA = PrB. C. VrA = VrB. D. When circulating current at no-load = zero.
Two 30 AC generators are such that one has twice the linear dimensions of the other. The field windings of each are excited to give identical sinusoidal air gap flux density waveform. Both have the same number of stator slots and identical winding patterns. The conductors per slot in big generator in K times that of the smaller one. The value of K to get equal no-load voltage at same frequency is (a)8 (b) 8 1 (d) 7 (c) 4
50 KW, 240 V enduvi resistance of a generator with foreign excitation is 0.02 ohms. Generatorproduces rated voltage at rated load. Endüvi voltage and endüvi current at rated loadcalculate? If the output voltage is kept constant at 240V and the output power is reduced to 45 KWfind the enduvi tension necessary for this?
.Two dc shunt generators A and B are rated at 100 and 150 kW at 110 V respectively, Their external load characteristics may be considered as straight line. The voltage drop In the terminal voltage from no-load to full-load is 10 v for A and 20 V for B. Determine the operating voltage when these generators are operated in parallel to supply a load of 220 kW.
The type generator field winding is supplied from the external D.C. source. separately excited Compound Shunt Self excited