The column shown in the figure is subjected to shear force Vu parallel to the 550 mm side. Allowable concrete shear stress for shear parallel to the 550 mm side. Allowable concrete shear stress for shear parallel to the 550 mm side is 0.85 MPa. Concrete strength f'c = 25 MPa and steel strength for longitudinal reinforcement is 414 MPa and for confining reinforcements is 275 MPa. The ties are all 12 mm in diameter with clear cover of 40 mm. 700 10-25mm Ø C. d. 12 mm Ø 40 mm 1. Calculate the required spacing of hoop reinforcement due to a factored shear force of Vu = 490 KN. a. 230 mm 180 mm 260 mm 74 mm 98 mm 550 mm C. b. 210 mm d. 2. Determine the maximum spacing of transverse reinforcement in accordance with Section 5.21.4.4.2. a. 150 mm C. 134.2 mm b. 146.3 mm d. 137.5 mm 3. Calculate the required spacing of transverse reinforcement in accordance with the Special Provisions for Seismic Design. a. 85 mm b. 91 mm

The column shown in the figure is subjected to shear force Vu parallel to the 550 mm side. Allowable concrete shear stress for shear parallel to the 550 mm side. Allowable concrete shear stress for shear parallel to the 550 mm side is 0.85 MPa. Concrete strength f'c = 25 MPa and steel strength for longitudinal reinforcement is 414 MPa and for confining reinforcements is 275 MPa. The ties are all 12 mm in diameter with clear cover of 40 mm. 700 10-25mm Ø C. d. 12 mm Ø 40 mm 1. Calculate the required spacing of hoop reinforcement due to a factored shear force of Vu = 490 KN. a. 230 mm 180 mm 260 mm 74 mm 98 mm 550 mm C. b. 210 mm d. 2. Determine the maximum spacing of transverse reinforcement in accordance with Section 5.21.4.4.2. a. 150 mm C. 134.2 mm b. 146.3 mm d. 137.5 mm 3. Calculate the required spacing of transverse reinforcement in accordance with the Special Provisions for Seismic Design. a. 85 mm b. 91 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Figure 2 shows a simply supported beam and the cross section at midspan. The beam supports a uniform service (unfactored) dead load consisting of its own weight plus 1.4 kips/ft and a uniform service (unfactored) live load of 1.5 kips/ft. The concrete strength is 3500 psi, and the yield strength of the reinforcement is 60,000 psi. The concrete is normal-weight concrete. Use load (Table 5.3.1) and strength reduction factors from AC1318-14. For the midspan section shown in Fig. P4-1b, compute Mn and show that it exceeds Mu. @ (b) 3 No. 9 bars WD = 1.4 kips/ft plus weight of beam 1.5 kips/ft WL H 12 in. 20 ft TT 21.5 in. 24 in. + Figure 2.
6. ESTIMATION OF QUANTITIES OF STEEL & R.C.C. ELEMENTS EPU Example 1: Estimate the Slab reinforcement for the given figure below. All the straight bottom bars are 10mm@400mm c/c. All offset bars 12mm@400mm c/c, All Additional Top bars 12mm@400mm c/c. The slab thickness is 150mm. Assume cover is 25mm & wall thickness20cm 0.45 0.45 3.70 4.70 0.45 0.45 3.70 5.20 3.10 1.60 150
Situation: A beam has a width of 300 mm and total depth of 600 mm strength f'c-36 MPa. Steel yield strength fy=415 MPa The section is to be reinforced for tension only and the effective concrete cover is 65 mm. Which of the following most nearly gives the value of our balanced steel ratio? a. 0.00370 b. 0.03456 C. 0.02860 d. 0.03522 Which of the following most nearly gives the value of our balanced distance of the cuter most fiber of compression fiber to our neutral axis? a. 313.256 mm b. 354.68 mm C. 333.333 mm d. 322.435 mm Which of the following most nearly gives the value of our balanced depth of compression block? a. 248.412 mm b. 266.2676 mm C. 301.478 mm d. 281.261 mm
A rectangular beam with a width of (9536/1150)-in,and effective depth of (9536/900)in is Reinforced with a single high strength steel bar that has a cross- sectional area of 0.42 in2.The bar has a normal tensile strength of 145 ksi, linear stress-strain curve to failure, and a strain at failure of 1.8 percent. The concrete strength fc= 6000 psi. Calculate the nominal flexural strength of the section.
Problem 2: A reinforced concrete beam has a width of 300 mm and a total depth of 550 mm. Effective cover to centroid of tension bars is 60mm. Compressive reinforcement (if required) will be placed at d’ = 60mm. f’c = 21 MPa and fy = 415 MPa. The Follow 2010/2015 NSCP provision and use ? = 0.90 for flexure. a.) Determine the required area of steel reinforcement, As, if the beam carries a factored moment of 79 kN-m. b.) Determine the required area of steel reinforcement, As, if the beam carries a factored moment of 193 kN-m. c.) Determine the required area of steel reinforcement, As, if the beam carries a factored moment of 402 kN-m.
Considering the nominal shear stress on concrete is f = 0.83 MPa. Calculate the allowable max spacing for 2-legged 10 mm stirrups? Use simplified calculation for Vc. Beam dimensions are 397 x 754 mm. Effective cover of steel reinforcement = 70 mm fy = 275 MPa Spacing should be in multiples of 10 mm. NOTE: USE STORED VALUES IN YOUR CALCULATION
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.2 m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-∅25 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places.
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As
Fill in the blanks: Determine the required tension steel area of the T beam with given properties below. Width of flange bf= 500 mm Width of web bw = 400mm Thickness of flange tf 140 mm Effective depth d = 380 mm Effective concrete covering d' = 75 mm Compressive strength of concrete fc' = 30 MPa Yield stress of steel bar fy = 300 MPa Mu = 448 kN-m As = mm2 CS Scanned with CamScanner
Considering the nominal shear stress on concrete is fv = 0.78 MPA. Calculate the allowable max spacing for 2-legged 10mm stirrups?. Use simplified calculation for Vc. Beam dimensions are 392 x 729 mm Effective cover of steel reinforcement = 70 mm Fy = 275 MPA Spacing should be multiples of 10mm
considering the nominal shear stress on concrete is fv=0.9 mpa calculate the allowable max spacing for 2 legged 10mm stirrups? use simplified calculation for Vc. Beam dimensions are 350x794mm effective cover of steel reinforcement = 70mm fy=275mpa spacing should be in multiples of 10mm
O Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu:= 30-MPa fy:= 450-MPa b:= 280-mm d:= 510-mm A, 2410-mm d':= 50-mm A's:= 628-mm² b A', d'