The characteristic equation of a control system is given as 1 + KG (s) H (s) = s +8s2 + 10s + K = 0, The objective is to investigate the stability of the system. What is the critical value of the gain K (round your answer to whole number, no decimal places)? Hint: Compute the value of K at the jw crossing.

The characteristic equation of a control system is given as 1 + KG (s) H (s) = s +8s2 + 10s + K = 0, The objective is to investigate the stability of the system. What is the critical value of the gain K (round your answer to whole number, no decimal places)? Hint: Compute the value of K at the jw crossing.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

Q2. Perform the following subtraction using l's and 2's complement method (Show step by step process) (i) (11010)2 – (10100)2 (ii) (1000101)2 – (1010100)2
The value of d20/dt2 for a synchronous machine, rated 50MVA, 60HZ, M% = 1.02MJ.s/degree, and Pa = 3.5Mw, machine is %3D O a. 4.356 rad/s2 O b. 0.424 rad/s2 O c. 3.431 rad/s2 O d. 2.358 rad/s2
Q1: Two forces act on the hook shown in figure. Determine the magnitude and direction of the resultant using Parallelogram Law. 600 N (Ans. R=910.241 N, angle=50.328° with horizontal) 400 N 20
Part 2: Subtraction of Two numbers In.arithmetic. unitsthesubtraction is transformed into an addition by adding the..complement. Se AB. means At (-B) = A+ complement of B The operation A =B might be: A>B, the result is positive, there will be an end carry A< B, the result is negative, written in the complemented form, no end carry Part a) fill its table. P-Q 7-5 5-3 9-9 4-bit binary adder P3 P2 P, Po Q3 Q2 Q1 10 1c 10 What is the 1b fupction of this bit? CI Figure 1: Circuit 1 CO Question: What is the function of the invertor in the circuit? Answer:
What's the maximum percent overshoot for this system with its closed-loop poles as shown? Jo Select one: O a. 64% O b. 15.7% O c. 14.9% O d. 33.6% O e. 21.5%
Explain why this is the equation for nodal analysis. I need to know how it became negative and positive. Why did Vs1 and Vs2 became negative? Why did Vs3 became positive and so on?
Moving to another question will save this response. Question 6 A shunt generator delivers 350A at 230 V and the resistance of the shunt field and armature are 50 Q and 0.03 Q respectively. the generated e.m.f. equals to 239.138 V 243.638 V 235.138 V 240.638 V A Moving to another question will save this response. I'm Cortana. Ask me anything. DELL
Q3) In a two-excitation and two-pole machine, the rotor and stator of both poles are prominent relations The inductor of the rotor and stator is as follows: Lss =(0.5 + 0.2cos20) H Lrr =(0.8 + 0.3cos20) H Lsr =0.7coseH The resistance of the windings is zero. If the rotor is in the position 0 =60 ° and flows from the stator A sinusoid with an effective value of 10A passes and the rotor winding is short, medium torque Calculate the impact on the rotor
we Q2/ what Ms meant by Pulsse Moduletim? why need PM ?
Find the current l4 for the figure shown below. 100A 40A 12 I1 80A 13 15 10A 14? a. 100A O b. 400A c. 200A O d. 150A
Find the values of K₁ and K₂ to yield a peak time of 1.5 seconds and a settling time of 3.2 seconds for the closed-loop system's step response. R(s) + OK₁=0.8984, K₂=0.04 OK₁=0.5197, K₂=0.045 OK₁=0.5949, K₂=0.05 ⒸK₁=0.4218, K₂=0.06 K₁ 10 s(s+ 2) K₂s C(s)
The electrical equivalent of mechanical load in induction machine is? a. r2/s b. r2*(1-s)/s c. r2/(1-s) d. r2