The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 3.4 kN when 0 = 33°, determine the force Prequired on the lever and the corresponding tension T₂ for this position. Assume that the surface under A is perfectly smooth.Assume a = 100 mm, b = 460 mm.T₁Answers:P =T₂ =ii9ABKN2KN2bTopocesT₂ The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the weight of the structure comparedwith the applied loads. Is the knowledge of the size of the structure necessary?3L60°Answers:Ay=Dy = iDx=HPB3LC60° 60°E2LLLL30°2LD

Disclaimer: “Since you have asked multiple question, we will solve the first question for you. If…

The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 3.4 kN when 9 = 33°, determine the force P required on the lever and the corresponding tension T2 for this position. Assume that the surface under A is perfectly smooth. Assume a = 100 mm, b = 460 mm. T₁ Answers: P= i T₂= i 9 A B KN KN T₂

The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 3.4 kN when 9 = 33°, determine the force P required on the lever and the corresponding tension T2 for this position. Assume that the surface under A is perfectly smooth. Assume a = 100 mm, b = 460 mm. T₁ Answers: P= i T₂= i 9 A B KN KN T₂

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Draw the FBD and set up the equations to solve the problem. Compute the tensile force in each cord. В A 105° 90° C 30 30 75° D 300 lb 400 lb
16. ao The drawing shows a rectangular piece of wood. The forces applied to corners B and D have the same magnitude of 12 N and are directed parallel to the long and short sides of the rectangle. The long side of the rectangle is twice as long as the short side. An axis of ro- tation is shown perpendicular to the plane of the rectangle at its center. A third force (not shown in the drawing) is applied to cor- ner A, directed along the short side of the rectangle (either toward B or away from B), such that the piece of wood is at equilib- rium. Find the magnitude and direction of the force applied to corner A. A D Axis Problem 16
Figure Fw 40° CG mg FT ▼ Calculate the tension Fr in the wire that supports the 42 kg beam shown in the figure(Figure 1). Express your answer using two significant figures. FT = 320 N ✓ Correct Part B Previous Answers A Calculate the magnitude of the force Fw exerted by the wall on the beam. Express your answer using two significant figures. Fw = 320 N Part C Previous Answers ✓ Correct ✔
Figure out tension in C2 and angle. Please show all computations. thanks G= سعدت G 30N 60° SON Figure out the tension in J 11/11 C₂ = ? cable г and the angle.
The forces are in static equilibrium. The 140 lb force is directed along the x-axis and the 300 lb force is directed along the negative z-axis. What is the angle between R and the z-axis? Provide your answer in degrees, but do not include units in your answer. Z X R ex лог 140lb A 1-50, 80, 160) lb By 300 lb Y
Problem 01: A force 200 N is directed as shown in figure. Determine the X and Y components of the force. Express your final answer in Kilonewton. 200 N 30° Problem 02: Determine the components of the 30u-N force directed down to the right at a slope of 2 to 3 as shown F = 300 N Problem 03: The components of a certain force are defined by . Determine the magnitude and inclination of of the resultant with the x-axis. Draw/plot your answer.
a) Cables AC and BC are connected to lifting points A & B, and joined together at C as shown in Figure Q1a. The angle = 200 and angle B = 50°. If the tension in each cable is 3.75 KN, calculate the force (F) and the angle a required to maintain point C in static equilibrium. Give your answers for F in kilonewtons (kN) and the angle a in degrees to two decimal places. A 3 F α B O
Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation which contains that force as the only unknown. The forces are positive if in tension, negative if in compression. 3.0 m BC= Answers: BE= A 3.0 m EF= G i i i B 3.0 m 3.0 m F 1.9 m E 3.0 m 20.0 KN KN KN kN D
PART A) What is the maximum force that can be applied to a bone whose minimum cross-sectional area is 3.0cm^2? (This is approximately the cross-sectional area of a tibia, or shin bone, at its narrowest point.) Express your answer using two significant figures. PART B) Estimate the maximum height from which a 70kg man could jump and not fracture the tibia. Take the time between when he first touches the floor and when he has stopped to be 0.006s, and assume that the stress is distributed equally between his legs. Express your answer using two significant figures. Thank you!!!
When the load L is 4.7 m from point C, the tension T in the cable has a magnitude of 5.4 kN. Express T as a vector using the unit vectors i and j. Assume a = 4.7 m, b = 2 m, c = 4.3m. T x j) kN L b Answer: T = (i it i
A cable stretched between the fixed supports A and B is under a tension T of 1.4 kN. Express the tension as a vector using the unit vectors i and j, first, as a force Tд acting on A and second, as a force Tg acting on B. 520 mm A 320 mm y | 1 L Answers: TA= i TB=(i i+ i+ Mi i B j) kN j) kN
A cable stretched between the fixed supports A and B is under a tension T of 2.3 kN. Express the tension as a vector using the unit vectors i and j, first, as a force TA acting on A and second, as a force Tg acting on B. 760 mm Α' 490 mm Answers: TA-i TB-i i+ i i+ i B j) kN j) kN