The cantilever beam consists of a rectangular structural steel tube shape [E = 200 GPa; 1= 350 × 106 mm²]. Assume P = 50 kN, w = 20 kN/m, LAB = 1.50 m, and LBc = 2.50 m. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Laa Determine the component of the beam deflection at point A due to only the uniformly distributed load of w = 20 kN/m. Answer: VAw= mm. Lac

The cantilever beam consists of a rectangular structural steel tube shape [E = 200 GPa; 1= 350 × 106 mm²]. Assume P = 50 kN, w = 20 kN/m, LAB = 1.50 m, and LBc = 2.50 m. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Laa Determine the component of the beam deflection at point A due to only the uniformly distributed load of w = 20 kN/m. Answer: VAw= mm. Lac

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1730 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 210 kip-ft, P = 13 kips, LAB = 3.8 ft, LBC= 5.7 ft. МА V A Answer: (a) VA = (b) VB= LAB P B in. in. LBC C X
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1900 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume Ma = 190 kip-ft, P= 19 kips, LAB = 3.0 ft, Lgc = 4.5 ft. MA LAB LBC Answer: (a) VA= in. (b) vg = in.
J- A distributed load op w (kulm) is applied over the entire tength OF a simply supported beam Gm long . The beam section is as shown. Determine the maximum value OF w iF Of Ś 1OMP , and yE 800KP. 80 mm X 200 mm 360mm 200mm
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I-1730 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 210 kip-ft, P = 13 kips, LAB = 3.8 ft, LBC = 5.7 ft. MA A Answer: (a) VA = (b) VB = LAB P B in. in. LBC C - X
Five forces are applied to the beam trolley as shown. Determine the y-coordinate of the point on the y-axis through which the stand-alone resultant R must pass if F = 6.8 kN and 8 = 20°. Point O is at the center of the I-beam. 2.4 kN - 630 mm 70 mm 2.2 kN 350 mm 1.0 kN 1.4 kN F Answer: y = mm the tolerance is +/-2%
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1860 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 180 kip-ft, P = 12 kips, LAB = 3.8 ft, LBC = 5.7 ft. MA A B LAB LBC Answer: (a) VA = in. (b) VB = in.
Current Attempt in Progress The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; = 1990 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA= 250 kip-ft, P= 14 kips, LAB = 4.1 ft, LBc = 6.2 ft. MA LAB LBC Answer: in. (a) VA- in. (b) VB - 4. Submi Attempts: 0 of 1 used Save for Later
%V9 lI1. . V:OA and shear stresses for the beam 9KN SKN/m 10 KN/m B A. C + Im 3m 2m 3m 200mm 350mm Option 1 The cantilever steel beam as shown below has the rectangular cross section shown, determine the maximum displacement of the beam use E=200 GPa for the modulus of elasticity 200mm 4 KN/m 6 KN .m 350mm 2m 2m 1m Option 1 Submit This form was created inside of University of Mosul. Report Abuse Google Forms II
02) The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmax = 1936x(0.5). 2. IfG =30 GPa find the angle of twist at the free end of beam. Y 10 kN 25 NA 120 mm 15 500 mm Good Luck and be Green
The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; I = 370 × 106 mm4). For the loading shown, determine the beam deflection vc at point C. Assume P = 51 kN, w = 30 kN/m, LAB = LBC = 3.3 m, LcD = 1.9 m. B C D LAB LBC LCD Answer: vc = -17.22 mm.
А L B 425 mm C 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs). b) Determine the final width and thickness of the Aluminum bar. (1) Your Answer:
EX3: For the beam shown in the figure below. Find maximum allowable ive load(P)that the beam can carry(in addirion to its own weight)causing un cracking of the beam, As=4000mm?. Effective cover =75mm Use fe' = 25 Mpa, fy = 400Mpa. |P P d= 500mm 300mm