Answered: The cable AB prevents bar OA from…

The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 800 N, determine the n- and t- components of this force acting on point A of the bar.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An eye bolt is used to attach 3 cables to a steel plate. The tension in the three cables create F1=200 lbf, F2=250 lbf, and F3=100 Ibf with 0 = 30 degrees and p=44 degrees. If the eye bolt is in equilibrium, what is the y-component of the sum of other forces on the bolt (force from the nut and plate on the bolt) ? If you add up %3D the three force vectors, the sum other force you are looking for will just be in the opposite direction to put the eye bolt in equilibrium. The y-direction is positive going up. For example, if you find the sum of forces 1, 2, and 3 are 100 Ibf going up, then the other forces in the y-direction must be pointing to the down (-100 lbf) to put the eye bolt in equilibrium. Eye bolt steel plate Nut & Washer esc DOO D00 F4 F3 AA %24 F10
Problem 05 The resultant of the three cable tensions acting on the flagpole is the force R acting vertically at O and T3 = 500 N. %3D 8 m B. T3=500 C. -y. 3 m 3 m T2 D 2 m T1 Find the value of T1. 2 Find the value of T2. 3 Find the value of R.
W=200# word by zonil risdi vino 2.11 A laborer is hoisting a weight, W = 200#, by pulling on a rope as shown. Determine the force F required to hold the weight in the position shown if the resultant of F and W acts along the axis of the boom. 20 2X51290104 29buliogom silint 808 30 q12
Q5/A) From the figure below, determine the reaction force at pin C. A 000 0.6 m 10 kN 0.6 m 0.8 m 60° 0.4 m 6 kN OB
The structure consists of a spring CD and a solid member ABC with a slot at B. The peg at B fits loosely into the slot at B and can hence be interpreted as a smooth support. The unstretched length of the spring is 80 mm. 50 mm 150 mm 50 mm A D C B k = 600 N/m 1.1 Draw separate free-body diagrams of member ABC and the spring CD. 1.2 Comment on the existence of two-force members and three-force members in this system. 1.3 Determine the reactions at A and B on the member ABC
Please help. Please make sure you clearly state how you got the numbers you got and why you are using them. Also please make sure you clearly put your formulas and label your units along the numbers that you are using. In the following frame ilustration, F1s 60 N and F2 is 9 N. What is the tension in the cable AB and the reaction force vector necessary to keep the system in static equilibrium? Give the X component reaction force at C( for an x axis going left to right). Also please solve for the rest of the 3 unknowns please. Thank you
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. kys Part 1 B 3.1 m AD 50° CD Answers: AD = The Free-Body diagram for joint D is drawn assuming that all internal forces are in tension. Solve for the forces in AD and CD. The forces are positive if in tension, negative if in compression. 50 CD = i 6.2 m 50 D 50° 3600 N 3600 N N N
The wheels, axle, and handles of a wheelbarrow W=62N. The load chamber and its contents weigh Wl=575N. The drawing chose leave to Forsyth and different wheelbarrow designs to support the wheelbarrow and equilibrium the man's hands apply a force to the handles that is directly vertically upward. consider the rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the Man's force for both designs
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
4 A ski resort chair lift has towers spaced 38 m horizontaly appart. The upper tower is 15 m higher than the previous tower. If the chairs are 12 m horizontally appart and the first chair is 5 m past the lower tower what is the tension on both ends of the cable? 1:37:01 Book The mass of each chair is 350 Kg and the height above the lower tower for each chair's attachment to the cable is 0.58537 m, 4 m, 9.4244 m. Lower Tower Cable Tension = Upper Tower Cable Tension = kN. KN.
A load weighing P kN aswith AB, AC and AD cables such asare carried. Points A and B are x-axis, Cand D points are on the y-z plane.Specific to your name in the data tableAB, AC and AD cable using ratingsCalculate the forces. P (kn) = 440 L1 (m) = 11 L2 (m) = 10 L3 (m) = 16 L4 (m) = 18 L5 (m) = 16 L6 (m) = 5
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal.