The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T = 10 °C, determine the average normal stress in each member when T2 = 45 °C. Also, how far will the collar be displaced? The cross-sectional area of each member is 1130 mm?. B. -1 m - -0.6 m-

The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T = 10 °C, determine the average normal stress in each member when T2 = 45 °C. Also, how far will the collar be displaced? The cross-sectional area of each member is 1130 mm?. B. -1 m - -0.6 m-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4.1 The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T.
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 2300 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 (1) Aluminum B (2) Copper Answer: in, AL = i
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E, = 10000 ksi] alloy. The length of segment (1) is L, = 70 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 98 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of 8z = 2100 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 Aluminum B Сорer Answer: in. AL = i
Compound axial member ABC has a uniform diameter of d = 1.50 in. Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 80 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 112 in. When axial force P is applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 1700 pin./in. in longitudinal direction. What is the total elongation of member ABC? L2 (1) d Aluminum В (2) Сopper
2- A steel pod is stretek between two rigid walls ard carries a tensile Coad 4GO0ON at c f the allowatle Stress is not to excred 130 MPa at -4C, what is the minimum the nd? diameter f ard E= J00 GPa. Figure: ST L
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m Sm A B L= 6m 9o kN L-4m A= 0.04 m A = 0.0 6m² E=200 GAa E=80 GPa
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. %3D Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. %3D When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 1500 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L1 P L2 A Aluminum В d Copper c'P Answer: AL = in. %3D
3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and cross-sectional area of 22.5 mm?. Member (2) is a short aluminum of initial length 50 mm and cross-sectional area of 40 mm?. The modulus of elasticity of the steel wire is 200 GPa and the aluminum block is 70 GPa. a) Draw the deflected shape of the rigid member and clearly label the deformation of members (1) and (2). b) Write the equilibrium and compatibility equations needed to solve the problem along with the supporting sketches. Hint: Be sure to carefully consider if the members are elongating or shortening; this must be represented mathematically. c) Calculate the internal forces in both axial members and clearly indicate tension or compression. [Ans. to Check: F2 = 535 N]
3. The rigid bar weighs 5 kN/m, is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises 20°C after a load W = 150 kN is applied. A (mm?) a (FC) E (GPa) Steel rod 300 11.7 x 10-6 200 Bronze rod 1400 18.9 x 10-6 83 Bronze | 3 m Steel 1.5 m ►| 1.0 m 2.5 m 2 m W
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontalbefore the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. STEEL Lm A-400 mm E-200 GPa BRONZE L-5m A-500 mm E-80 GPa 3m
The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P if the working stresses are 240 MPa for steel and 120 MPa for aluminum, and the total elongation of the bar is not to exceed 6 mm. 1.5 m 2 m 2P P Steel Aluminum A = 18 mm2 E = 70 GPa A = 12 mm2 E = 200 GPa %3D
The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity is 3.7E6 psi for aluminum and 5.6E6 psi for brass, determine the maximum shearing stress in cylinder AB And cylinder BC in ksi. 1 Aluminum T= 19.6 kip-in. Brass A - 1.4 in. B <-2.1 in. C 10 in. 15 in.