The bending stresses on an element are: om 25,00 psi or= 21,667 psi. There is a stress raiser with stress concentration value of Kf = 1.4. The material has Su = 90,000 psi, Sy = 80,000 psi, Se = 40,000 psi. Assuming there will be no plastic yielding of the material, find the value of = LONE Flli bir

The bending stresses on an element are: om 25,00 psi or= 21,667 psi. There is a stress raiser with stress concentration value of Kf = 1.4. The material has Su = 90,000 psi, Sy = 80,000 psi, Se = 40,000 psi. Assuming there will be no plastic yielding of the material, find the value of = LONE Flli bir

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The components of plane stress at a critical point on a steel shell are shown in the figure below. The yield stress (Gy) of the material in simple tension is 250 MPa. 60 MPa 40 MPa 70 MPa (a) Determine the magnitude of the principal stresses and maximum shear stress. Sketch these on appropriately orientated elements. (b) Calculate the factor of safety against yield on the basis of i. Tresca failure criterion ii. Von Mises failure criterion
Steel Stress-Strain diagram. Which of the following statements is NOT correct? Engineering stress is the stress computed using the original area and not the necking down area. The constant stress region is called the yield plateau or plastic range. The linear portion is also called the plastic range. The proportional limit, elastic limit, upper and lower yield points are very close to one another and are treated as a single point called the yield point.
A state of stress is specified in the figure shown. Determine the principal stress oy (mPa) if P =-20 mPa and y = 15 mPa P V
At a point in a component, the state of stress is shown on the element below. Assume that the stress magnitudes are s,-7150 psi and Sy - 4475 psi. The stresses act in the directions indicated in the figuure. Determine the magnitude of the absolute maximum shear stress that acts at the point. Answer: Tmax psi
The stress strain diagram for an unknown material is shown. Determine tha strain at point E. (Unitless) Do not round off and complete solution. Thanks.
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0 and if the elastic mođulus and length of the bar is 200 GPa and 2 m respectively, calculate the elongation in mm of the bar corresponding to the maximum load it can support. (А) 5 (в) 2.5 1.25 D) 0.625
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 185 mm, a wall thickness of 5 mm, and a length of 5.0 m. The pipe supports a compressive load of 675 kN. After the temperature of the pipe drops 39°C, determine:(a) the axial deformation of the pipe.(b) the change in diameter of the pipe.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. P = 10 kN a. What is the stress (MPa) in the Bronze material? b. What is the stress in Aluminum in MPa? c. What is the stress in Steel in MPa?
Determine the value of load P if At = 30 °C and the stress in bronze is limited to 132 MPa. Aluminum Bronze A = 600 mm? A = 500 mm? L= 2.0 m L= 2.50 m E = 70 GPa a = 23x10/ °C E = 83 GPa a = 18.90x10/ °C |c B D A O 2.0 m 3.0 m 1.0 m
Determine Value of x if the Normal stress at rod is equal to the stress at rectangular pipe A =400 mm2 F = 8kN Rod A =650 mm² rectangular Pipe
30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E = 69 GPa. If Poisson's Ratio is 0.33, what will be the lateral strain? E= 6/8 v = -E(lateral)/(axial)