The bear cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 14 mm d = 100 mm t = 4.8 mm Additionally: • The area of each pipe is A = 1436 mm². • The moment of inertia of the entire bear cross section about the z centroidal axis is lz=140920000 mm². If the bearn will be subjected to a shear force of V = 170 kN, determine the shear stress at point H, located at y = 100 mm above the z centroidal axis.

The bear cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 14 mm d = 100 mm t = 4.8 mm Additionally: • The area of each pipe is A = 1436 mm². • The moment of inertia of the entire bear cross section about the z centroidal axis is lz=140920000 mm². If the bearn will be subjected to a shear force of V = 170 kN, determine the shear stress at point H, located at y = 100 mm above the z centroidal axis.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 470 mm tw = 16 mm d = 120 mm t = 6.4 mm Additionally: • The area of each pipe is A = 2284 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 316830000 mm4. If the beam will be subjected to a shear force of V = 255 kN, determine the shear stress at point K, located at yK = 80 mm below the z centroidal axis.
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 430 mm t₁ = 14mm d = 110 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3028 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is lz= 325870000 mm². If the beam will be subjected to a shear force of V=245 kN, determine the shear stress at point H, located at y = 110 mm above the z centroidal axis. d H.V Answer: TH= x Z MPa Уи YK H K
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 430 mm tw = 16 mm d = 110 mm t= 6.4 mm Additionally: • The area of each pipe is A = 2083 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is lz=241870000 mm4. If the beam will be subjected to a shear force of V=235 kN, determine the shear stress at point K, located at yk = 70 mm below the z centroidal axis. H H K Answer: TK = z MPa Уи Yk
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 430 mm tw = 14 mm d = 110 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3028 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 325870000 mm4. If the beam will be subjected to a shear force of V = 225 kN, determine the shear stress at point H, located at yH = 110 mm above the z centroidal axis.
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 12 mm d = 100 mm t = 6.4 mm Additionally: • The area of each pipe is A = 1882 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is lz=171660000 mm4. If the beam will be subjected to a shear force of V = 120 kN, determine the shear stress at point H, located at yμ = 100 mm above the z centroidal axis. H Hv K Answer: TH= X MPa Ун Ук K Iv
А L B 425 mm C 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs). b) Determine the final width and thickness of the Aluminum bar. (1) Your Answer:
3. The length of 2-mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 1.5 mm exists between the end B of the rigid beam ACB and a contact point E. If E = 200 GPa, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D X 0.25 m 20 kg A 1.5 mm C 0.08 m 0.32 m E
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1= 0.8 m; B2= 1.0 m; B3= 0.6 m. Determine the axial load acting on bar B1 in kN. 35KN В1 B2 ВЗ 10KN 15KN 30KN
A HA He 1 m L 1 m
A beam of the cross section shown is extruded from an aluminum alloy for which Oy= 250 MPa and ou= 450 MPa. Using a factor of safety of 3.00, determine the largest couple that can be applied to the beam when it is bent about the z-axis. Take x = 18 mm. M₂ 24 mm 80 mm 24 mm X The largest couple that can be applied to the beam when it is bent about the z-axis is kN-m.
Figure 1 shows a steel bar AB that has a rectangular cross-section. If it is pin connected at its ends, determine the maximum allowable intensity w of the distributed load that can be applied to BC without causing bar AB to buckle. Use a factor of safety with respect to buckling of 2.5. E = 200 GPa, Oy = 360 MPa. Q1 w kN/m В 5 m 3 m 30 mm Section A-A iy + + 20mm 20 mm, Section A-A Figure 1
Each of the three uniform 1200-mm bars shown in Figure has a mass of 30 kg. The bars are welded together into the configuration shown and they are suspended by three vertical wires. Bars AB and BC lie in the horizontal x-y plane, and the third bar lies in a plane parallel to the x-z plane. Compute the tension in wire A, wire B and Wire C