The assembly shown consists of a flywheel, a counterweight, and a bolt that attaches the counterweight to the flywheel. The flywheel is uniform with mass per area of 3 g/mm² and has a 40 mm diameter hole as shown. Determine the mass mc of the counterweight so that the center of mass of the assembly is at point O. The counterweight is attached to the flywheel by a bolt with mass mg = 800 g that is screwed into a 10 mm diameter hole that passes completely through the flywheel. (Round the final answer to four decimal places.) flywheel 40 mm counterweight and bolt mc, mB 45 mm 100 mm 50 mm

The assembly shown consists of a flywheel, a counterweight, and a bolt that attaches the counterweight to the flywheel. The flywheel is uniform with mass per area of 3 g/mm² and has a 40 mm diameter hole as shown. Determine the mass mc of the counterweight so that the center of mass of the assembly is at point O. The counterweight is attached to the flywheel by a bolt with mass mg = 800 g that is screwed into a 10 mm diameter hole that passes completely through the flywheel. (Round the final answer to four decimal places.) flywheel 40 mm counterweight and bolt mc, mB 45 mm 100 mm 50 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.26P: The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A...

See similar textbooks

Similar questions

Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the unknowns.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
The compound arrangement of the pan scale is shown. Part A: If the mass on the pan scale is 4 kg, determine the distance d of the 20-g mass to keep the scale in balance. Part B: Determine the horizontal component at pin A. Part C: Determine the vertical component at pin A. Part D: Determine the horzontal component at pin B. Part E: Determine the vertical component at pin B. Part F: Determine the horizontal component at pin C. Part G: Determine the vertical component at pin C.
The homogeneous box has mass m. The magnitude of force Pis slowly increased until motion occurs. Motion could occur as slipping or tipping and you must decide which occurs first. Find the value of P which first causes motion. P 30° Ho= 0.40 B 2.2 d Answer: P = i mg
The figure shows composite shape comprising of two long slender rod bodies. The horizontal body has a length of 1.2m and mass 3kg; the second body has a length 0.4m and mass 1kg. The centre of gravity of each of the individual bodies can be found at their geometric centre, labelled G₁ and G2₂ in the figure. The composite shape has symmetry about the x axis, thus its centre of gravity lies on the line 'y=0' as depicted in the figure. Calculate the x coordinate of the centre of gravity of the composite shape. O O 0.95 m 0.75 m 0.50 m Don't Know 0.60 m G₁ G₂
Find the center of mass of the system shown if M1= 10 kg, and M2= 20 kg. Mr M: 3. 2.
The homogeneous box has mass m. The magnitude of force Pis slowly increased until motion occurs. Motion could occur as slipping or tipping and you must decide which occurs first. Find the value of P which first causes motion. A 33° = 0.40 B 2.0 d
Locate mass A at 35 mm from support X.Locate mass B at 96.5 mm from support X. Locate mass C at 122.7 mm from support X.Position mass A at zero degrees and D at 90o from A. A B C D mass(kg) 0.021 0.044 0.059 0.019 essentric length(r) m 0.036 0.025 0.034 0.036 6.1. Use the graphical method to determine the angular position of masses B and C.6.2. Calculate the position of mass D from support X.6.3. If the shaft rotates at 150 r.p.m calculate the dynamic force experienced by the bearings.
The compound pulley shown has a weight of 1600 N and the radius of gyration (k = 2 m). Find the tension in the cord supporting the 1500-N weight (TA) and tension supporting the 2000-N weight (TB) as shown
1. Determine the second mass moments I,, 3d- 3d - I, and J,for the plate shown. The plate has uniform thickness, t, normal to the plane of the figure, and uniform mass den- sity, p. The parameters d, e, t and are given. 6d 4d Radius = 2d
Determine the equivalent spring constant of the system where the spring will be located in the position of k1. k1=1N/m, k2=5N/m (answer in N/m) * Sphere, mass m, No slip Bell crank lever, - mass moment of inertia Jo 06. m
A truck is driving over a scale at a weight station. When the front wheels drive over the scale, the scale reads 5800 N. When the rear wheels drive over the scale, it reads 6500 N. The distance between the front and rear wheels is 3.20 m Determine the distance between the front wheels and the truck's center of gravity.