The allowable shear stress is 10 ksi in the shaft shown. Determine the minimum required outside diameter if section is hollow circle with inside diameter of 1 inch Draw the torque diagram in your solution sheet. Answer in inches and 2 decimal places The allowable shear stress is 10ksi in the shaft shown. Determine the minimum required outside diameter if section is hollow circle with inside diameter of linch. Draw the torque diagram in your solution sheet. Answer in inches and 2 decimal places 8,000 lb-in. 19.000 lb-in. 4,000 lb-in. 7,000 lb-in B

The allowable shear stress is 10 ksi in the shaft shown. Determine the minimum required outside diameter if section is hollow circle with inside diameter of 1 inch Draw the torque diagram in your solution sheet. Answer in inches and 2 decimal places The allowable shear stress is 10ksi in the shaft shown. Determine the minimum required outside diameter if section is hollow circle with inside diameter of linch. Draw the torque diagram in your solution sheet. Answer in inches and 2 decimal places 8,000 lb-in. 19.000 lb-in. 4,000 lb-in. 7,000 lb-in B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 261 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 194 mm in diameter. If the torque that can be applied is 8728 Nm without exceeding a shearing stress of 52.59 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places. Add vour answer
Please solve, include the diagrams, and do not copy from other bartleby answers. Handwritten solution is more preferred than typed. A 40-mm diameter, 522-mm length shaft is drilled, for a part of its length L1, to a 20 mm diameter and for the remaining length L2 to a 30 mm diameter drill hole. If the allowable shear stress is 86 MPa, find the maximum power that the shaft can transmit at a speed of 226 rev/min. If the angle of twist in the length of 20 mm diameter drill hole is equal to that in the 30 mm diameter drill hole, find the length of the shaft that has been drilled to 20 mm and 30 mm diameter.
Answer the following problem. Show your complete solution. Use 4 decimal places. Calculate the diameter of the shaft required to transmit 45 kw at 120 rpm. The maximum torque is likely to exceed the mean by 30% for a maximum permissible shear stress of 55. Calculate also the angle of twist for a length of 2m.
A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 268 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 195 mm in diameter. If the torque that can be applied is 7275 Nm without exceeding a shearing stress of 49.52 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.
(Please input the FBD together with the answer) A flanged bolt coupling consists of nine-in diameter bolts equally spaced around a bolt circle 15 inches in diameter. Determine the torque capacity of the coupling if the shear stress in the bolt is limited to 5000 psi.
The shaft is subjected to a steady load of 36,000 in-lb at a shear stress of 10,000 psi. Compute the diameter of the said shaft in inches. A. 1 7/8 B. 2 ¼ C. 3 D. 2 ¾ Please solve the Problem elaborately and Refer Machine Elements and Stresses Equations from the figures or use other shortcut Methods you have or you may Solve both or in more different methods the better ?. Your solution will be use as reference for my Future Board Exam preparation/review/study. Thank you so much dear your work will be appreciated much and rated excellently.
Two solid circular shafts are connected by two rigid gears. Note shaft ab is a composite shaft. Determine the angle of twist at point 'a' in degrees to two decimal places. solid shaft 60 in $= 11/1535 TL GJ J=TY/2r4 b composite shaft C 35 in bearing Notes:- gear b radius = 6.0 in - gear c radius = 4.0 in - shaft ab outer radius= 1.5 in - shaft ab inner radius= 1.1 in - shaft cd radius= 1.0 in - shaft ab inner shear modulus = 12000 ki - shaft ab outer shear modulus = 3000 ksi - shaft cd shear modulus = 12000 ksi outer portion inner portion shaft ab cross-section 2.86 in-kip
The number of teeth on the driving sprocket chain is 50, used to change up of speed from 500 r.p.m. to 850 r.p.m. Find the number of teeth on the driven sprocket. If the pitch circle diameter of the driven sprocket is 350 mm and center to center distance between the two sprockets is 1000 mm, determine the pitch and length of the chain.
The axes of two parallel shafts are to be 600mm apart approximately, and have to be connected by spur gear, having a circular pitch of 30 mm. If gear A rotate at 200 rpm and gear B rotate at 600 rpm, find the number of teeth on each gear.
For the steel shaft shown in Fig. Draw a torque diagram for the shaft. 30 kN-m 15 kN-m 5 kN-m B. 10 kN-m 40 kN-m
QUESTION 2 A shaft rotates at 300 rpm. 1). If it carries a spur gear that delivers 5 hp to a mating gear and the spur gear has the diametrical pitch of 10, pressure angle of 20°, and 80 teeth, determine a). The resultant force exerted on the shaft = Ib 2). If it carries a sprocket that delivers 4 hp to a mating sprocket and the sprocket has the pitch diameter of 6", determine b). The force exerted on the shaft Ib 3). If it carries a "flat-belt pulley" (Note: NOT V-Belt Drive) that delivers 8hp to another flat-belt pulley and the pitch diameter of the pulley is 20", determine C). The force exerted on the shaft: Ib
PROBLEM 2 As an Engineer, you have been tasked by your superiors to determine the shear stress and the angle of twist in sections AB & BC of the shaft loaded in the figure shown below. Given that you used the formular; 7 = to find the shear stress, and used: 0= to find the angle of twist. Where all the symbols have their usual meanings. Show mathematically, how these two formulae are derived. Explain in word and use free- body-diagrams where necessary for clarification. 600 mm CO 5 kNm 1200 mm 100 mm 8 kNm 20 kN