The accumulated value would not be maintained if the timer was an RTO type instead of a TON.
Q: 5. For this buffered circuit, sketch V.(t) by inspection: R₁ = 6 KQ; R₂ = 20 KQ; C = 10 µμF; Vc(0) =…
A: Given data, R1=6Kohm. R2=20kohm . C=10uF. Vc(0)=9v. We have to find vc(t) (sketch) Circuit:
Q: Suppose you have a mask M = 0xF0020031 and a register P = 0xABCDEF01. What are the results of the…
A:
Q: 2- In the circuit shown in fig (3), calculate the current through the resistor R when its resistor…
A: The current through the load resistor has been calculated
Q: 2. What is meant by energy efficiency of a transformer? A 20-KVA transformer has a maximum…
A:
Q: The single-phase bridge rectifier of Figure below is required to supply an average voltage of…
A: Answer: given that a full wave bridge rectifier average voltage VDC = 300 V resistance R = 15 ohms…
Q: An iron ring has its mean length of flux path as 60 cm and its cross sectional area as 15 cm^2. Its…
A: SOLUTION:Data given in the question Length of flux path (l) = 60 cm Cross sectional area (A) = 15…
Q: Question-2 Consider the following circuit, and given: lin(s) Iin (s) = â 2s-1 (s + 1)(s² +25) 400 Ω…
A:
Q: 5.1-4 Determine the Nyquist sampling rate and the Nyquist sampling interval for the signals: (a)…
A: In this question We need to sampling rate and sampling interval. We know Sampling frequency ws =…
Q: Three transformers, e ach rated 25 MVA, 38. 1 /3.81 kV, are connected Star – Delta with a balanced…
A: Given: Three transformers, each rated 25 MVA, 38.1/3.81 kV, are connected Star – Delta with a…
Q: orrect Answer Question 7 The Nyquist Plot of the open loop transfer function G(s) in the unity…
A:
Q: expressions using Karnaugh map : (a) A.B.C+ A.B.C+ A.B.C+ A.B.C+A.B.C+A.B.C+ A.B…
A:
Q: In the circuit shown in the given figure, device A receives 2 kW at 0.8 pf lagging, device Breceives…
A: In this question We need to determine the total current I. We know Complex power S= VI* VA
Q: Given a standard size 2-input NAND gate followed by two inverters and a load of 100C. What is the…
A: Given data There are two input NAND which is getting followed by two inverters. The load is 100C. To…
Q: An iron cored toroid of relative permeability 980 has a mean length of 120 cm and core are of…
A: Given A iron core toroid: relative permeability μr= 980 has a mean length of lc=120 cm and core…
Q: 2. A facility manager replaces all the TS lights in an office when they have reached 80% of their…
A: Group re-lamping: It is process in which all the old lights are replaced by new ones on…
Q: 11=8 A (9) 14 12, R1=300 www R3= 100 13 R2= 240 15 R4=80 Resp: 12=3 A; 13=5 A; 14=3 A: 15= 8 A
A:
Q: Obtain the power factor ( PF ) , apparent power ( S ) ,Real Power (P) &the Reactive Power (Q ) of a…
A:
Q: Calculate the center frequency, the bandwidth, and the quality factor of a bandpass filter with an…
A:
Q: Figure a be 25 ΜΗ 15iA 25 nF 1 of 1 is 2502 Part A Find Zab, in the circuit shown in (Figure 1) when…
A: In this question we need to find the equivalent impedance between terminal a and b.
Q: Two Coils A and B are kept in parallel plane, such that 70% of the flux produced by coil A link with…
A: Solution: We have given N=Number of turns i.e For A coil =10000 & For B Coil 12000 I=Current…
Q: Question 4 What is the rms value of current i(t) = Imcos(wt+0;)? O IM√2 O IM√3 O IM slash√2 O IM…
A:
Q: What are the drawbacks of hydrogen fuel used in fuel cells? What is the most notable technical…
A: We need to tell about drawbacks of hydrogen fuel used in fuel cells and losses of Direct methanol…
Q: For the circuit shown, determine the equivalent voltage source in Volts where 11-10 A, 12-1 A, R1-16…
A: We need to find out voltage source for given circuit.
Q: In relation to Vc why is RE equal to 330 x10^-3 when it is 330 ohms? Thank you
A: For this bjt problem, Rc is changed to Rc=330ohm. We need to find IC VCE, The power dissipated in Rc…
Q: 9. An alternating voltage of 10 volt at a frequency of 159 kHz is applied across a capacitor of 0.01…
A:
Q: (a) Write, as a series, the z-transform of the number sequence generated by sampling the time…
A:
Q: 8.38 Refer to the circuit in Fig. 8.86. Calculate i(t) for t > 0. 5(1-u(t)) A ماليا F= rele www i(t)…
A:
Q: 6. A 20 HP motor operates at full load for 7,000 hours each year at an efficiency of 91%. It is…
A: Given,Old motor -20HP with 91%.New motor -20HP with 93%.
Q: Find RL in the given network in order to achieve maximum power transfer. ww 2kQ 12 V 2kQ 32k02 2 k
A: Given data, Circuit diagram is given as,
Q: emts 8₁ = 19.9 V. 8₂-10.7 V, and 83-5.40 V, and the resistances are each 2.000. What are the (a)…
A:
Q: The diode in the circuit of Figure 2 has a non-linear terminal characteristic shown in figure 3.…
A: Given: A circuit, with diode characteristics as, where Vs=0.1 cosωt V, V1=2 V, To find: iD and…
Q: 6. The power spectral density of a white noise process is 10 and it is passed through an ideally…
A: Given data Power spectral density is 10. Frequency, f=50 Hz Bandwidth=4 Hz To find out We have to…
Q: Problem 5. Calculate the cross-sectional area, in mm², of a piece of copper wire, 40 m in length and…
A:
Q: Applying source transformation and current dividers calculate the current IR1
A: The required parameters can be calculated by using the source transformation and current division…
Q: For the circuit below find vo(t) when i(0)=5A and v(t)=0 202 v(t) U U U i(t) 0.4 H m This circuit is…
A: It is a basic RL transient circuit We need to find out the following statements. Circuit
Q: 1- By using Thevenin's Theorem, solve the circuit in Fig (1) and calculate the value of current and…
A: I am doing first one with theoretical calculations for the given fig (1)
Q: 5. The air handling unit for an office has a 20 HP motor that operates at full speed. An energy…
A:
Q: 2. 1V Resistor ww TKO VI
A:
Q: 6V Use Norton's theorem to find V, in the network given below. 6 k 2 k 2000/ 3 mA 4 ΚΩ 4k02
A: In this question we need to find the voltage Vo using Norton theorem.
Q: 15 Part 1 of 2 L1 Inputs O O-S1 0-S2 2 O-S3 O O-S4 o-S5 1 o S6 3 5- 6 7 8 S1 HE S2 HF S3 HE S4 = HE…
A: Given a ladder logic program If switches S2 and S3 are turned ON. To find Outputs PL1 and PL2 come…
Q: a) Determine (b) Determine the real Fourier series of x(t) the complex Fourier series of x(t) wi T₂…
A: Given waveform of x(t) To determine: Real or trigonometric Fourier series of x(t) Complex Fourier…
Q: H(o)= 5(jw + 2) ja(ja + 10)
A: We need to find out bode plot for given transfer function. The transfer function is given below: As…
Q: An iron ring has its mean length of flux path as 60 cm and its cross sectional area as 15 cm^2. Its…
A:
Q: (2) Generate and plot the following sequences (a) x1 [n] = 38[n+2] +26[n] - 8[n- 3] +56[n-7], -5 ≤n≤…
A: To do: We have to generate and plot following signals using MATLAB Code.
Q: 1. What is the resistance of this network measured from terminals a-b? 2. What is the resistance of…
A:
Q: Find the current id at time t TU = S. 10 COS cos (10t+) V 0.2 H id 3. id ia (₁) (20t +) V 4 cos (20t…
A: Here we have two sources of different frequencies so we have to use the superposition to calculate…
Q: For a particular BJT, Is = 5×10–15 A and I's = 10-13 A, calculate the collector current knowing that…
A: It is given that: Is=5x10-15 A,Is'=10-13 A,VBE=0.7 V,VCE=0.15 VVT=25.9 mV
Q: For the periodic signal shown below: 류 12 (a) What is the period? (b) Compute the Fourier Series Ce…
A:
Q: can you also do d and e?
A: Given: For the circuit, To find: d) Power provided by battery. Confirm that the total power…
Q: Question In the circuit below the switch has been closed for a long time, at t = Os the switch is…
A:
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 1 images
- a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate thecomplete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform.(Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.)(Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.)IV) Convert Decimal to Hexadecimal (a) 974510 (b) 2976.5410 V) Convert from Binary to Hexadecimal (a) 10010110101012 (b) 111011101.010101012 VI) Convert from Hexadecimal to Binary (a) 7CAB516 (b) AF2.12B161What will be the state of a MOD64 counter after 90 input pulses if the starting state=000000?A.100100B.011010C.010110D.011100 2.A MOD 32 counter is holding the count 101112. What will the count be after 31 clock pulses?A.10100B.10010C.10000D.10110
- parity generator design, construct and test a circuit that generates an even parity bit ffrom four messages bits . use XOR gates. adding one more XOR gate, expand the circuit so that it generates an odd parity bit also.a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate the complete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform. (Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.) (Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.) 1/6 Pat DigClock Part List OFFTIME = SuS DSTM1 ONTIME = DELAY= STARTVAL = 0 OPPVAL = 1 Sus EUK FleStim AC Lbrajes Design Cache b) Read the specification of 74LS47 (BCD-to-7-Segment Decoder shown in Appendix) to see how the logic IC operates to drive a 7-segment LED display. Draw the circuit connection of the decade counter in (a) and the decoder to display the count value on the 7-segment LED display. Further explain why common anode…Draw logic diagram for half adder and full adder circuit using Logisim Software
- Using MOSFETs, implement the following Logic Function: f = AB'+C+DA. Write a Verilog HDL code for Verilog code for a for 6-bit unsigned up counter B. Write test bench code of the circuit in the figure: DỊ40) 5-bit Full Adder 5-bit 5-bit Up - Counter DFF Ckd) Draw the schematics of 4-bit synchronous and asynchronous MOD-8 counters and comment on their pros and cons. e) Calculate the noise margin for a logic gate with the following logic levels: VIL = 1.1 V, VIH = 3.2 V, VOL = 0.6 V, VOH = 4.0 V.
- Below is an example of an NMOS logic circuit. For all of the MOSFETs in the circuit below, assume V = 1 V and k = 50 mA/V². th W R₂ = 5600 PEETHIPPIN R₁ - 4700 M3 M₁ M. 0 a. Indicate and verify the state of each MOSFET and V for the following input combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use R approximation for linear operation and three significant ds(on) figures for the voltages. 오 Ao SV whyComputer Science & Engineering Define BCD counter. A circuit consist of five cascaded BCD counters. Find the range of counting of the cascaded sequence.VI) Convert from Hexadecimal to Binary (1 Mark) (a) 78BAC516 (b) ACDC2.12B16 VII) Convert from (2 Marks) (1) (ii) Find the binary equivalent of the BCD number (0100 1001 1001.0100 0011 0011)BCD Find the BCD equivalent of the binary number 110100010.101102