The 2.3-in.-diameter drive shaft AB on the helicopter in (Figure 1) is subjected to an axial tension of 10 000 lb and a torque of 345 lb⋅ft. Determine the principal stresses and the maximum in-plane shear stress that act at a point on the surface of the shaft.

The 2.3-in.-diameter drive shaft AB on the helicopter in (Figure 1) is subjected to an axial tension of 10 000 lb and a torque of 345 lb⋅ft. Determine the principal stresses and the maximum in-plane shear stress that act at a point on the surface of the shaft.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.24P: The stresses acting on a stress element on the arm of a power excavator (see figure) are ax= 52 MPa...

See similar textbooks

Related questions

Q: Water of density 62.3 lbm/ft³ and dynamic viscosity 2.02 x 10-5 lbf-s/ft² flows with velocity 4 ft/s…

A: The density of the water,(ρ)=62.3 lbm/ft3 The dynamic viscosity, (μ)=2.02×10-5 lbf.s/ft2 The…

Q: Determine the distance of the center of mass of the bracket shown measured from the base. Use three…

Q: Water flows in a horizontal pipe 3.2-in diameter; the diameter of the pipe is reduced to 1.8 in. If…

Q: For figure Q3, find rivet diameter, where T = 100MPa ? 20mm O 20mm- 30mm ga O 9 0 9 30mm 4 KN 25…

A: Explanation is given in handwritten answer

Q: Calculate the steady-state temperatures for nodes 1 to 9 in Figure P3-58. h = 25 W/m² °C T = 5°C 2 3

Q: The aircraft link is made from an A002 steel rod (Figure 1) Figure 1 of 1 > Part A Determine the…

Q: A tanker carrying tolueneis unloaded to an onshore storage tank using the ship’s pumps. The pipeline…

A: Given:D=225 mm=0.225 mL=900 mLs=200 mLd=700 mρ=874 kg/m3μ=0.62 cP=0.00062 Pa.sPvapor=0.037…

Q: The 20-1b rectangular plate has a natural period of vibration t = 0.4 s, as it oscillates around the…

A: Weight of rectangular plate, W=20 lbTime period of vibration, t=0.4 sDimension of plate,a=3 ftb=5 ft

Q: (Q1) Find the number of cycle required to increase the crack lengul (0.3 mm) to (0.4 mm). The…

Q: A 10 ft long steel member with pinned ends (i.e., pinned-pinned) is used as a column. The member…

A: From question, Length of steel shaft, L = 10ft=10×12 inch= 120 inch Thickness of member…

Q: Air at 2.5 bar, 400 K is extracted from a main jet engine compressor for cabin cooling. The…

Q: Q3.8) A microphone operates on the principle of a diaphragm gage with a capacitance pickup. Suppose…

A: Maximum pressure fluctuation = 0.029 psi Diaphragm frequency = 10000 Hz Diameter of the diaphragm =…

Q: Problem 3 The 2-kg ball of negligible size is fired from point A with an initial velocity of 14 m/s…

Q: 118. Medical The bones of the forearm (radius and ulna) are hinged to the humerus at the elbow…

Q: Required information Problem 07.093 - Point loads applied to a cable with level supports - DEPENDENT…

A: The forces are P1=2 kN, P2=4 kN, P3=6 kN The distance dc is 4 m.

Q: A particle of mass m moves along the x-axis such that its acceleration is d²x dt² = 8x³. - -X. (a)…

A: Expression of acceleration,d2xdt2=8x3-xBoundary condition, at x=0, U=0

Q: bullet points

A: some machines set up process for convenience are given as - Define the scope and objectives of…

Q: A dormitory at a large university, built 50 years ago, has exterior walls constructed of L - 25-…

Q: Determine the final measurements of the length and diameter of the following bar that is subjected…

Q: Consider the compound beam shown in (Figure 1). Suppose that P1 = 950 N, P2 = 1500 N, w = 550 N/m,…

A: handwritten solution attached

Q: plz give an orginal solution, im having trouble following textbook solution. thanks! only…

A: Given-Information: Mass of block B=mB=10kgEdge weight, 22 kg To-Determine: a. Acceleration of B. b.…

Q: In the figure below, Gears B and C represent a compound gear and have the following details. The…

A: number of teeth t A=100 tB=40 tc=80 tD=20 input torque Ti=42 Nm speed of gear A NA=2400 rev/min…

Q: 3 m 250 N/m -2 m B 500 N 2 m

Q: Instructions: In this exercise, incomplete relationships are set up among fluid conductors and…

A: Here we have to complete the relationship among fluid conductors and connectors by choosing…

Q: Give the following beam: cm x < * 6m 2kN/m B a) Determine the equations for shear and moment as a…

Q: The length of the ship’s water-plane area is 70 m. The lengths of the equidistantly spaced half…

Q: A simply supported beam of length L = 1 m (A = hinged support, B = Roller support) is shown above…

A: Given data :- L = 1 m a = 0.4 m P = 1.7 kN (A) By…

Q: Fluid Dynamics (Similtude) If the fluid oscillates at a frequency of 10 rad/s in a 100 mm…

Q: A reservoirs water level is 200m above a pelton wheel jet. If the jet diameter is 20mm and the…

Q: Q.4) Determine the maximum mass m of cylinder for which the system shown below is in Static…

A: The maximum mass of the cylinder. Given: The mass of the block is M=50 kg. The coefficient of…

Q: Example 2: Refrigerant R-134a enter the compressor of a has a refrigerantor a superheared vapor at…

A: Given:Refrigerant=R134aRefrigerant condition at compressor inlet, P1=0.14 MPa, T1=-10oCRefrigerant…

Q: A stream of water (p= 1000 kg/m³) enters a steady- state flow diverter shown in the figure. The…

A: given a= 0.5 m b=1 m c=0.4m d=0.2m mass of the diverter M=60Kg density of water =1000kg/m3 cross…

Q: The electric fan is mounted on a swivel support such that the fan rotates about the z axis at a…

Q: Instructions: In this exercise, incomplete relationships are set up among fluid conductors and…

A: Here we have to complete the relationship among fluid conductors and connectors by choosing…

Q: The 10-kg block-spring-damper system is damped. (Figure 1) Figure k = 60 N/m www c= 80 N-s/m Part A…

Q: 5.) Determine the thickness of a outside diameter of 100 mm hollow shaft having an if it is…

A: According to the given data T=5403.58 N.m D=100mm τ=60 Mpa G=83 GPa θ=0.5° per meter length of the…

Q: 10. A radio controlled car travels with a constant speed of 2 m/s along a path described by y = 30…

A: Y= 30sin(0.2x) V= 2 m/s find maximum magnitude of acceleration that car experience along the path

Q: An auxiliary power unit (APU) is a relatively small, self-contained generator used in aircraft to…

A: To find: The probability that the failure occurs at the 20th flight test?

Q: A standard oil-gas horizontal separator, the gas stream has flow rate around 3.5MMscfd, the amount…

A: handwritten solution attached

Q: What does the stator entry flow angle mean? why is the relative velocity and absolute velocities in…

A: To explain: What does the stator entry flow angle mean? why is the relative velocity and absolute…

Q: Q6: The U-bend in the figure below is connected to a flow system by flexible hoses that transmit no…

A: The internal diameter of the pipe is d=3 in. The flow rate of water is Q=600 gal/min. The density of…

Q: Estimate the flow rate in gallons per minute from a 12 inches diameter pipe when the water velocity…

Q: A 10 mm diameter galvanised iron pipe transports water at a flow rate of 0.092 kg/s to a chemical…

A: Diameter of the pipe.D=10 mm=0.010 m The mass flow rate of the water, m.=0.092 kg/s. The length of…

Q: Helium contained in a closed, rigid tank, initially at 50°C, 4 bar, and a volume of 2.2 m³, is…

Q: The air in the reservoir has an absolute pressure of 450 kPa and a temperature of 30°C. The throat…

A: Introduction The nozzle allows very powerful air to exit the engine. It is well-known for its…

Q: The 20-kg block is subjected to the action of the harmonic force F = (90 cos 6t) N, where t is in…

Q: Outside air at a temperature of 25°C is drawn into the duct and then heated along the duct at 234…

A: To Find : The mach number at section 2 The temperature at the section 2 The pressure at the section…

Q: Problem 07.094 - Deflection of cable with level supports with know maximum tension Three loads P₁ =…

A: The forces are P1=2.8 kN, P2=4.8 kN, P3=6.8 kN The maximum tension is 27 kN.

Q: The mine car and its contents shown in (Figure 1) have a total mass of 4.5 Mg and a center of…

Q: A dormitory at a large university, built 50 years ago, has exterior walls constructed of L. = 25-…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

show formula and calculation as fast as , don't hold the question for longer time. 1) The 2.3-in.-diameter drive shaft AB on the helicopter in (Figure 1) is subjected to an axial tension of 10 000 lb and a torque of 345 lb⋅ft. Determine the principal stresses and the maximum in-plane shear stress that act at a point on the surface of the shaft.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Define the term

VIEW

Step 2: Calculation of principal stresses

VIEW

Step 3: Calculation of maximum in-plane shear stress

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
The stresses acting on a stress element on the arm of a power excavator (see figure) are ax= 52 MPa and txy= 33 MPa (sec figure). What is the allowable range of values for the stress if the maximum shear stress is limited to = 37 MPa?
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
A propeller shaft subjected to combined torsion and axial thrust is designed to resist a shear stress of 57 MPa and a compressive stress of 105 MPa (see figure). (a) Determine the principal stresses and show them on a sketch of a properly oriented element. (b) Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?