The 13.5-lb disk rests on the 5-lb plate. A cord is wrapped around the periphery of the disk and attached to the wall at B. A torque M = 40 lb-ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at D having a coefficient of kinetic friction of μ = 0.2. Neglect the mass of the cord. (Figure 1) Figure M = 40 lb-ft 1.25 ft 3 ft 1 of 1

The 13.5-lb disk rests on the 5-lb plate. A cord is wrapped around the periphery of the disk and attached to the wall at B. A torque M = 40 lb-ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at D having a coefficient of kinetic friction of μ = 0.2. Neglect the mass of the cord. (Figure 1) Figure M = 40 lb-ft 1.25 ft 3 ft 1 of 1

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.23P: The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of...

See similar textbooks

Similar questions

The 40-kghomogeneous disk is placed on a frictionless inclined surface and held in equilibrium by the horizontal force P and a couple C (C is not shown on the figure). Find P and C.
The 3600-lb car with rear wheel drive is attempting to push the 4500-lb crate. The center of gravity of the car is at G, and the coefficients of static friction are 0.6 at B and 0.2 at C. Determine if the crate will slide. (The car pulling the crate is analyzed in Prob. 7.19.)
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
3. Two blocks, each of mass m, are attached to the ends of a massless rod which pivots as shown in Fig. 8-43. Initially the rod is held in the horizontal position and then released. Calculate the magnitude and direction of the net torque on this system when it is first released m ·l₂ m
The motorcycle in the figure has a mass of m1 kg and its center of mass is at G1. The mass of the driver is m2 kg and the center of mass is at G2. Since there is fs between the wheels and the asphalt, determine whether it is possible for the driver to lift the front wheel off the ground. Neglect the mass of the wheels and assume that the front wheel can spin freely. a=0.41 m b= 0.39 m c= 0.75 m d= 0.25 m e=0.58 m m1=120 kg m2= 77 kg fs=0.82
The circular bar shown in the figure is vertical.fixed by the support at point A in the plane. AThe spring constant connected to the support is k = 40 N/m. Broadcastingundeformed length, arc between circle ABis the distance. C fitting (bracelet) with a mass of 200 grams,connected to the spring and move in a frictionless circle bar.can. When the union is θ = 30° from the rest positionis being released. In this case, relative to point B of the fittingthe highest height it can reach and the highestcalculate the speed
4. The mine car and its contents have a total mass of 6000 kg and a centre of gravity at G. If the coefficient of static friction 10 kN between the wheels and the 0.9 m •G tracks is u = 0.4 when the wheels are locked, find the normal force acting on the front wheels at B and the rear 0.15 m 0.6 m - 1.5 m wheels at A when the brakes at both A and B are locked. Does the car move? [Ans. NA = 16.5 kN, Ng =42.3 kN, the car does not move] %3D lyp
The smooth surface of the vertical cam is defined in part by the curver - (0.2 cos 0+ 0.3) m. (Figure 1) Figure If the forked rod is rotating with a constant angular velocity of 4 rad/s, determine the force the cam and the rod exert on the 1.1-kg roller when 0-30°. The attached spring has a stiffnesss k- 30 N/m and an unstretched length of 0.1 m. Express your answers in newtons using three significant figures separated by a comma. Neam, Frod = Submit AΣo↓ vec Previous Answers Request Answer * Incorrect; Try Again; 3 attempts remaining < Return to Assignment Provide Feedback Kwi| ? N
2. Find the horizontal force P to start the motion of any part of the system of three blocks resting upon one another as shown. The weight of the blocks are W-300 KN, Ws= 100 KN and Wc =200 KN. Between A and B μ=0.30, between C and B, μ =0.20 and between C and the ground, p=0.10. 1 sni brod nog 02.0-4 B C 05.0-4 Solution: tamos quoy worla bre sosia asquar 005 300 en of jells400 N₁-300 F3 N-300- N₂=300 Assuming B and C will not move. F₁ = 300 (0.30) F₁ = 90 kN ne à bns A zelboß 1 P = 90 kN es ensla berb hebnu 02.0- y elin 05.0= q V in Celpris orllanimetsa MX 008 Assuming C will not move: al 1st F2=400 (0.20) = 80 kN OTE Bm ribirte F₂ vica Assuming the three blocks move: F3 = 0.10 (600) F3 = 60 kN P=60 KN Least force is 60 kN.
1.0m 3.0m 0.5m mi m2 PA N, 5. The drawing above shows two objects on a board supported at two locations. The m; = 40 kg (centered over P), m;=20 kg and m3=10 kg. c. Determine the force exerted by N2. (Take torques around P.) d. m2 rolls to the right. Just before the board starts to tip everything is balanced on N2 with no force on N1. Determine how far to the right of N2 m2 could roll without the board tipping. You might find it easier to take torques around a point rather than P.
3- Can the system in figure be in static equilibrium in the position shown? The uniform bar AB weight 500 lb, and the weight of block C is 300 lb .Friction at A is negligible and the coefficient of static friction is 0.4 at the other two contact. 10 ft В 30° C 50°
The uniform rod has a mass of 10 kg and rests on the inside the smooth ring at B and on the ground at A as shown in Figure Q3. Calculate the friction of static friction between the rod and the ground if the rod is on the verge of slipping. 0.5 m 0.2 m 30 A Figure Q3