The 0.6-lb particle is guided along the circular path using theslotted arm guide. Motion occurs in the horizontal plane withnegligible friction. Note that the circular part of the slot has theradius equal to 0.5 ft, and the radial position, r, is measured fromthe hinge and the angle is measured in the counter-clockwisedirection. If the arm has an angular velocity = 4 rad/sec andan angular acceleration 6 - 8 rad/sec² at the instant when 0 =30°, determine the force of the arm guide on the particle at theinstant. Present your answer in lb using 3 significant figures.0.5 ft00.5 ft.

Given-Information:- m = 0.6 lbr = 0.5 ftθ˙ = 4 rad/sθ¨ =8 rad/s2θ = 30° To-Determine:- Force of the…

that the circular part of the slot has the the radial position, r, is measured from is measured in the counter-clockwise an angular velocity = 4 rad/sec and 5 = 8 rad/sec² at the instant when 0 = of the arm guide on the particle at the

that the circular part of the slot has the the radial position, r, is measured from is measured in the counter-clockwise an angular velocity = 4 rad/sec and 5 = 8 rad/sec² at the instant when 0 = of the arm guide on the particle at the

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The helical path is wound around the circular cylinder with radiusR . The step h= 2*pi*R. The object A is sliding through the path guide under gravity (acting in the negative zdirection). There is no air resistance 1)Draw the force diagrams in (theta ,Z ) plane (tangent to the cylinder) and in( r,theta ) plane. 2) If the initial speed is 0, find the speed after 3 full circles. Given: R, g, m, u.[Hint: Use the work-energy principle.]
Z 0.4 m The crank OA rotates in the vertical plane with a constant clockwise angular velocity mo of 4.5 rad/s. For the position where OA is horizontal, find the angular acceleration (magnitude and direction) of link AB and the force acting on the light roller Bof the slender bar AB. The mass of the uniform bar AB is 10 kg. Neglect all frictional forces. 0.8 m 1.0 m Vg = 5 m/s
Part A The smooth surface of the vertical cam is defined in part by the curve r = (0.2 cos 0+0.3) m. The forked rod is rotating with an angular acceleration of 0 = 2 rad/s as shown in (Figure 1), and when 0 = 45°, the angular velocity is 6 = 6 rad/s. Determine the force the cam and the rod exert on the 1.8-kg roller at this instant. The attached spring has a stiffnesss k = 100 N/m and an unstretched length of 0.1 m. Express your answers in newtons using three significant figures separated by a comma. ? Neam, Frud = N Submit Request Answer Figure 1 of 1 Provide Feedback Next >
The spring-mounted 0.97-kg collar A oscillates along the horizontal rod, which is rotating at the constant angular rate 0 = 5.8 rad/s. At a certain instant, r is increasing at the rate of 910 mm/s. If the coefficient of kinetic friction between the collar and the rod is 0.68, calculate the friction force F exerted by the rod on the collar at this instant. Vertical Com Answer: Fi N
The homogeneous, solid cylinder with mass m = 4.8 kg and radius r = 0.24 m rolls along the inclined surface without slipping. If the initial angular velocity is w, = 2 rad/s (counterclockwise), and after a certain time lapse the angular velocity is w2 = 2.2 rad/s (clockwise), determine the magnitude of the linear impulse due to the frictional force during this time period. Let 0 = 46°.
The spring-mounted 0.90-kg collar A oscillates along the horizontal rod, which is rotating at the constant angular rate 0 = 6.2 rad/s. At a certain instant, r is increasing at the rate of 790 mm/s. If the coefficient of kinetic friction between the collar and the rod is 0.68, calculate the friction force Fexerted by the rod on the collar at this instant. Vertical (ונננננ Answer: F = i N
The spring-mounted 0.92-kg collar A oscillates along the horizontal rod, which is rotating at the constant angular rate 0 = 6.5 rad/s. At a certain instant, r is increasing at the rate of 850 mm/s. If the coefficient of kinetic friction between the collar and the rod is 0.52, calculate the friction force F exerted by the rod on the collar at this instant. Answer: Fi Vertical N
If the coefficient of static friction between the 50-lb roller and the ground is p, = 0.25, determine the maximum force P that can be applicd to the handle, so that roller rolls on the ground without slipping. Also, find the angular acceleration of the roller. Assume the roller to be a uniform cylinder. 15 ft 30
The flat circular disk rotates about a vertical axis through O with a slowly increasing angular velocity w. Prior to rotation, each of the 0.52-kg sliding blocks has the position x = 28 mm with no force in its attached spring. Each spring has a stiffness of 430 N/m. Determine the value of x for each spring for a steady speed of 279 rev/min. Also calculate the normal force N exerted by the side of the slot on the block. The force N is positive if it pushes from the side labeled A. Neglect any friction between the blocks and the slots, and neglect the mass of the springs. (Hint: Sum forces along and normal to the slot.) Answers: X = wwwwwwww N = i i -74-74- mm mm mm N
The spring-held follower AB has a weight of 0.75 lb and moves back and forth as its end rolls on the contoured surface of the cam, where r=0.2 ft and z = (0.1sine) ft. If the cam is rotating at a constant rate of 6 rad/s, determine the force at the end A of the follower when e=90°. In this position the spring is compressed 0.4 ft. Neglect friction at the bearing C. z = 0.1 sin 20 0.2 ft e = 6 rad/s k = 12 lb/ft Fs FA- T
The 0.2-Kg pin P is constrained to move in the smooth curved slot. Which is defined by the lemniscater = rotation of the slotted arm OA, which has a constant clockwise angular velocity of ė when 0 = 0°,note that the motion is in the vertical plane, (b) the acceleration in the r and 0 direction. (0.6cos20) m. Its motion is controlled by the = -3 rad/s. Determine (a)-the force arm OA exerts on the pin P Answer: r(0.6 cos 26) m a, = -27 m/s? ag = 0 F = 1.96 N 21
The uniform rectangular block with the given dimensions is dropped from rest from the position shown. Corner A strikes the ledge at B and becomes latched to it. Determine the angular velocity w of the block immediately after it becomes attached to B. Also find the percentage n of energy loss during the corner attachment. Use the values h = 340 mm, b = 520 mm, and c = 810 mm. The angular velocity is positive if counterclockwise, negative if clockwise. Answers: ω- rad/s n = %