Suppose that an error occurred during the transmission of the 7/4 Hamming Code 1110111 of a binary code. a- Give the definition of a perfect code. b- Determine the coding efficiency of a (7, 4) Hamming code. c- Correct the error bit and write down the original binary code (without parity bits) which was meant to send.

Suppose that an error occurred during the transmission of the 7/4 Hamming Code 1110111 of a binary code. a- Give the definition of a perfect code. b- Determine the coding efficiency of a (7, 4) Hamming code. c- Correct the error bit and write down the original binary code (without parity bits) which was meant to send.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

1. What are the advantages of PCM system over other types of modulation systems? 2. What are the types of representing binary numbers? 3. The central operation in the generating PCM is the Digital to Analog (A/D) converter. Describe briefly the several techniques that are used in success system. 4. What is meant by the Quantization Partition and Quantization Codebook? 5. Discuss the obtained results.
Discussion: 1. What are the advantages of PCM system over other types of modulation systems? 2. What are the types of representing binary numbers? 3. The central operation in the generating PCM is the Digital to Analog (A/D) converter. Describe briefly the several techniques that are used in success system. 4. What is meant by the Quantization Partition and Quantization Codebook? 5. Discuss the obtained results.
1. What is the modulo of the circuit below? 2. Make a table of the count sequence. 3. A BCD counter can assume____discrete state. 4. A BCD counter can divide its input frequency by____. 5. A four-bit binary counter contains the number 0100. Nine inpulse occur. The new counter state is_____. 6. Design a 4-bit down counter.
An encoder a.Group of answer choices b.converts a binary code input to a single output c.Converts a singe input to a binary coded output d.Selects from many data sources e.Directs data to one of many data terminals
1-Design a 3 – bit binary decoder (3 – to --8 decoder), 2-Design a BCD – to – Decimal decoder. 3- Design a Binary Number – tọ – 7-segment decoder."
Write a Verilog code for 8-bit up/down counter for any type of Modeling.
4- Design the logic circuit of 4-to16 decoder using basic logic gates. Find its truth table and logic diagram. 5- What is the purpose of encoder circuit? 6- What is the purpose of decoder logic circuits?
VHDL Difference between function and task. What is logic data type.
1- Explain the operation of the PCM encoder used in module ED-2960F. 2- Discuss the advantages and disadvantages of the counter-type ADC. 3- Is the conversion time of the ADC constant or variable? What parameter does control it? 4- What are other types of ADCS? 5- Discuss the effect of changing the number of bits on the recovered analog
a) Implement decimal to BCD encoder. b) Implement full adder using decoder.
A combinational circuit that selects binary information from one of many input lines and directs it to a single output line is a multiplexer. a. an encoder. Ob. a decoder. C. a priority converter. none of the others. e.
1)-Convert the decimal NUMBER 1817.09375 to binary number showing the steps Integer part= Fractional part = 2)-Convert the binary NUMBER 11101110000. 10111 to decimal number Decimal no = 3)-Convert the decimal number 49622.970718384 into a HEX NUMBER showing the steps The integer part %3D The fractional part = 4)-Answer the following Hexadecimal to decimal conversion problem: Convert the HEX NUMBER 3198. CA3A to decimal number 5)-Convert the HEX NUMBER 3BF3. 45F8 to octal number showing the steps Integer part = Fractional part = 6)-Convert the octal NUMBER 2170. 2532 to hexadecimal number showing the steps Integer part = Fractional part =