Suppose r0= 0x20000080, and the memory layout is as follows:AddressData0x200000870x990x200000860xCC0x200000850x660x200000840x550x200000830x440x200000820x330x200000810x220x200000800x11Suppose the system is set as little-endian. What are the values of rl and r0 if the followinginstructions are executed separately?(1) LDR r1,[ro](2) LDR r1, [r0,#4](3) LDR r1,[ro],#4(4) LDR r1,[r0,#4]!

Let us examine the values of r1 and r0 for every instruction in a little-endian system. The…

Answered: Suppose r0= 0x20000080, and the memory…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Let (BX)=100H, DI=200H, DS=1200H, SI= FO02H, AX= 0105H, and the following memory content. what is the content of SI after executing the MOV SI, [DI+BX+7H] instructions? * Memory Memory address content 12300 11 12301 AA 12302 EF 12303 80 12304 47 12305 8D 12306 5A 12307 92 12308 C5 SI = EF80H SI = 80EFH SI = 92C5H SI = C592H
Question Vvv For a microprocessor similar to ATmega328p an 8 bit ADC uses a VREF = 3.3 V. When an analog read is executed the return value is 182. What Voltage is present on the input? Enter the value in the box provided in mV. Round to the nearest mV. No units are required . .Full explain this question and text typing work only We should answer our question within 2 hours takes more time then we will reduce Rating Dont ignore this line ..
4. Show how to connect two of the 6264C RAM chips symbolized in the figure below to produce a 16K X 8 RAM module. The circuit should not require any additional logic. Draw a memory map showing the address range of each RAM chip. A12 Inputs WE CS, CS, OE VO pins DATAQUT DATA Mode A, A WE Cs, cs, OE SRAM 8K x8 READ 1. 1. WRITE Output disable IN High Z High Z мсм 6264C Not selected (power down) X- don't care
Q13/Assume that the microprocessor can directly address 64K with a and 8 data pins The memory map for 16K x 8 RAM system that design by using 4KX8 RAM are None of them co0-DFFF, A000-BFFF, 8000-9FFF, 6000-7FFF co00-CFFF, DO00-DFFF, E000-EFFF, FO00-FFFF O 0000-1FFF , 2000-3FFF, 4000-5FFF, 6000-7FFF O E000-E7FF, DO00-D7FF, BO00-B7FF, 7000-77FF
Below is a 4-bit up-counter. What is the largest number of the counter if the initial state Q 3 Q 2 Q1Q0 =0011? (D 3 an Q 3 are MSB, and when Load = 1 and Count =1 the counter is loaded with the value D 3 ...D0) 4-bit counter Clock Q3 Load Count "I" or Vcc "I" or Vcc Do "1" or Vcc - D, Qi Q2 "0" or Gnd - D2 "0" or Gnd D3 Q3 1111 0011 1100 0110
bit numbers and store lower byte of the result in accumulator A and higher byte in accumulator B.. Similarly lower byte of 2nd number is stored in R2 and higher byte in R3. Now subtract these two 16 numbers in the RAM such that lower byte of 1t number is stored in R0 and higher byte in RI. manipulate 16 bits numbers as well. Write an assembly language program that stores two 16 bits 8051 is an 8-bit microcontroller that performs arithmetic on 8-bit numbers. However, we can Question#3: 8051 is an 8-bit microcontroller that performs arithmetic on 8-bit numbers. Howeve
The lowest address contained in the ROM memory is: A13 A12 All B 1 A10- El A 4 ROM dcs 0000 2D00 3C00 200 3D00 7D00 7C00 O00 OK 74LS138
An Intel 8085 processor is executing the program given below. MVI A, 10H MVI B, 10H BACK NOP : ADD B RLC JNC BACK HLT The number of times that the operation NOP will be executed is equal to
1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40 ADD R3, R1, R2 a) What will be the 8-bit result in Register R3 (in hex)? b) What is the 8-bit result in Register R3 (as unsigned decimal)? c) What is the 8-bit result in Register R3 (as signed decimal)? d) What will be the value of the carry (C) bit?
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Write program to load the content of memory location 0x0700 into register R3 then set D6,D7 and complement D4,D5 for date in R3 then store the result in memory location 0x0800 .
What is the hexadecimal value stored in Register A after the following assembler has executed? LDA #0x71 NOTA NOTA LDR B,#0x71 ADC A,B LDR B,#0xEB ADC A,B NOTA LDR B,#0xD5 ADC A,B LDR B,#0x53 SBC A,B LDR B,#0x19 SBC A,B LDR B,#0x5E SBC A,B

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS