SOLVE B. A hall 30 m long and 12 m wide is to be illuminated and the illumination required is 50 meter-meter candles. Calculate the number of lamps required taking a maintenance factor of 0.7 and utilization coefficient of 0.5, given that the output of the lamp to be used is rated 100 W, 1615 lumens

SOLVE B. A hall 30 m long and 12 m wide is to be illuminated and the illumination required is 50 meter-meter candles. Calculate the number of lamps required taking a maintenance factor of 0.7 and utilization coefficient of 0.5, given that the output of the lamp to be used is rated 100 W, 1615 lumens

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

el (a) Suppose the diagram of an electrical system is given in the Figure below. What is the probability that the system works? Assume the components fail independently. 0.7 0.95 0.9 'A 0.8 D
in a work environment 50 Hz 220V Find the following hardware in the power system 1.. .piece 100W incandescent filament lamp 2.power.. .kW efficient %88 power factor 0.85 asynchronous motor with 3.power 2000W a heater with power factor of the power system. .Calculate the capacity of the capacitor that needs to be added to the circuit in order to determine the places to be written in the blank
A 125-volt d-c generator whose internal resistance is 0.15 ohm is connected through a 0.45 ohm line resistor to charge two 90-volts storage batteries A and B in parallel. If the internal resistance of batteries A and B, respectively, 0.32 ohm and 0.4 ohm, what are the charging currents?
For the circuit shown in figure (2), Determine All values of power delivered and absorbed Upload your solution steps in blackboard assignment. 420 and 3240 4420 and 4420 2340 and 2340 6240 and 3240 Figure (2).pdf 18 A $25 2 8A100 n20n Figure (2)
A drawing office 10m X 5m having illumination of 200 Im/m2 which is to be provided by a number of 50 W lamp. Determine the number of required lamps if luminous efficiency of each lamps 10 Im/W. Consider both utilization and depreciation factors to be 1. Select one: O a. 20 lamps O b. 100 lamps O c. 10 lamps
Solve the following Numerical problems a. What is the Output Voltage of a battery that expends 7.2J of energy in moving 1C of charge? b. A 50-ohm load dissipates 200W of power. How much is the voltage and current across the load? c. If one branch of a 120-V power line is protected by a fuse of 20-A. Will the fuse carry 10-Ohm load? d. If total resistance of a series circuit is 280-Ohm. If one of the resistance is 160-Ohm. What is the sum of other two resistances?
PROBLEM SOLVING INSTRUCTION: Solve the following problems Write your solution on the spaces provided (5 points each) 1. Someone watches TV on average 4 hours each day. The TV is connected to a 220 V voltage so that the electric current flows through the TV is 0.65 Amperes. If the electric company charges P 0.042 per kWh. How much it will cost for using electric energy for TV for 1 month (30 days). 2. When a current of 1A flows through a wire, the drift velocity of the electrons is 0.9 mm/s. What will be the drift velocity of the electrons when a 2A current flows through another wire of the same material having double the length and double the area of cross section and same temperature. 3. A conductor whose diameter is 0.175 inch has a resistance of 0.5 ohm. The wire is drawn through a series of dies until its diameter is reduced by 0.095 inch. What is the resistance of the lengthened conductor? 4. If the certain conductor has an area of 356,400 CM, what is the radius of this conductor…
Q24. A voltmeter of (0- 300V) and Ammeter of (0- 20A) are connected in a circuit to measure the value of power input to the circuit. Both the meters are found with a limiting error of 1.1% on half-scale deflection. Calculate the following, when the voltmeter and ammeter shows 230 V and 10 A respectively. Limiting error voltage Limiting error power i. ii.
(b) A student sets up an electric circuit like the one shown in Figure Q1(b). i) Describe how a student would measure the current and voltage value for each component in the circuit in a laboratory. ii) By using nodal analysis method determine the value of current and voltage across the 42 resistor? iii) From the result obtained in Q1(b)(ii) please do explain why. 5V 6A 6A A Figure Q1(b) |
Figure 1 shows the circuit diagram of an automotive lighting system, and all lamps has 500 Q resistance. 3. a) Describe the characteristics of a parallel circuit in terms of resistance current and voltage. b) Determine: The current generated by the battery if the brake switch is closed The current generated by the battery if the light switch is closed iii. The current generated by the battery if the light switch and high-beam switch are closed i. i. iv. The current generated by the battery if all switches are closed high-beam switch Lights switch Brake switch Right Left Right Left Right Left Right Left Low-beam Brake lights High-beam headlights Tailights headlights 12V Figure 1
A) Find the equivalent resistor of the circle between points a and b?B) If a constant voltage source (15V) is placed between points a and b, calculate a valueCurrent iS
Figure 1 shows the circuit diagram of an automotive lighting system, and all lamps has 500 Q resistance. 3. a) Describe the characteristics of a parallel circuit in terms of resistance current and voltage. b) Determine: i. The current generated by the battery if the brake switch is closed ii. The current generated by the battery if the light switch is closed ii. The current generated by the battery if the light switch and high-beam switch are closed iv. The current generated by the battery if all switches are closed