Solve ALL FORCES and DRAW THE SHEAR FORCE (V-D) AND BENDING MOMENT (M-D) COMPLETELY of the following beam COMPUTE THE MAXIMUM HORIZONTAL SHEARING STRESS AT THEJUNCTION OF THE WEB AND THE FLANGE. COMPUTE THE MAXIMUM BENDINS STRESS - The beam shown below is composed of three 40 mm x 120 mm fastened together to form an l-beam. 5 kN/m 5 kN/m 4.5 m 4.5 m- Please compute MANUALLY for verification of my answer. Thanks!

Solve ALL FORCES and DRAW THE SHEAR FORCE (V-D) AND BENDING MOMENT (M-D) COMPLETELY of the following beam COMPUTE THE MAXIMUM HORIZONTAL SHEARING STRESS AT THEJUNCTION OF THE WEB AND THE FLANGE. COMPUTE THE MAXIMUM BENDINS STRESS - The beam shown below is composed of three 40 mm x 120 mm fastened together to form an l-beam. 5 kN/m 5 kN/m 4.5 m 4.5 m- Please compute MANUALLY for verification of my answer. Thanks!

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4.9 through 4.11 Two vertical forces are applied to a beam of the cross section shown. Determine the maximum tensile and com- pressive stresses in portion BC of the beam. 10 mm 10 mm 50 mm Fia. P4.10 50 mm 10 mm A BY 150 mm Q Search 10 kN 250 mm S C L 10 kN 150 mm CO D
1) DETERMINE TENSILE BENDING THE CROSS-SECTION BELOW. SOKN 20KN/m 3m THE MAXimum STRESSES OF THE B 30 кн/т Gm COMPRESSIVE Ано THE BEAM BEAM GIVEN 150MM SHOWIN 30mm 180mm 30mm
A cantilever beam AB, loaded by a uniform load (see figure), is applied on a channel section. If the cross section has the dimensions indicated and the moment of inertia about the z axis (the neutral axis) is | = 3.36 in a) Find the maximum tensile stress feuaxand maximum compressive stress fyMx b) Draw the shear and moment diagram 5.0 lb/ft 0.617 in. 2.269 in. 6.0 ft
QB4 BENDING STRESS The beam is loaded by one couple at each of its ends, the beam cross-section shown below (Figure QB4). Determine: a) The position of the horizontal neutral axis. b) The second moment of area of the section about the horizontal neutral axis. c) The values of the maximum tensile stress and the maximum compressive stress in the beam if it supports a maximum bending moment of 1200x10 N.mm and the base face is in tension. 150mm 50mm 250mm +50mm I 50mm 150mm Fig QB4
Q1: For the loaded simply supported beam shown in figure, if the allowable bending stress is 100 MPa determine: (1) the minimum value of the width (b). (2) the maximum shear stress in the section. 20mm 10mm 20 kN 120mm 3 kN/m 60mm 20 kN.m 10mm B 20mm 3m 1m 10mm 10mm
Determine (a) the maximum bending stress, (b) the maximum shearing stress due to V in the simply supported beam shown in the figure and (c) the shearing stress at a point 1m from the right support and 2 cm below the top. 5 cm 40 kN/m 16 kN m A 1-+-2 2 m m CF -2 m 16 cm
Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P at A. Diameter of wire CD is 1/8 of an inch and the diameter of the pin at B is 1/8 of an inch. Determine the tensile stress in wire CD and the direct shear stress in the pin at B. 150 P=300lb. -5 in- dw ↓ 1 4 in. D View a-a of B
Determine the maximum normal stress on a transverse plane in the straight portion of the structure shown below and clearly indicate where it occurs. The member is braced in the plane perpendicular to the plane of symmetry. Consider: (a) Section B-B shown below at the left (symmetric section). (b) Section B-B shown below (unsymmetric). 4 40 kN 750 mm 75 mm 50 mm 100 mm mm 09: Section B-B 100 mm A 150 mm 50 mm 30 mm 80 mm 20 mm 09 1200 mm Section B-B, part b
QUESTION 1 a) Calculate the position of the neutral axis and the value of the second moment of the beam with a cross section as shown in Figure 1(a). -216 mm- 72 mm Figure 1(a) b) If the beam of cross-sectional area Figure 1(a) that simply supported at both ends carries a uniformly distributed load, 1.5 kN/m along its 2m length. Determine the maximum tensile and maximum compressive stresses. 36 mm 108 mm QUESTION 2 a) A solid shaft of 50 mm diameter is subjected to 10 kNm torque. Determine the shear stress and angle of twist if its length is 2m. Given the rigidity of modulus is 90 GN/m². b) A solid steel shaft 5 m long with a shear stress of 80 MN/m² when twisted through an angle 4º. Given G= 83 GN/m², determine: i. The shaft diameter i. The power that can be transmitted by the shaft at 20 rpm.
calculate the location of the centroid, the second moments and product of area for the cross- section if; D = 67 mm, B = 41 mm & t = 2.41 mm A L Test beam A Strain gauge W (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 Strain gauge 2 b Strain gauge 3 a B (b) Location of Huggenberger strain gauges From these, calculate the orientation and position of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis).
on 2 If we know that the tensile force in the 20-mm-diameter tie rod BC is 10 kN, what is the average shear stress (in MPa) in the 10-mm-diameter pin at B. ered ed out of ng question B 30 7000 N 3 m
For the simply supported beam with the given cross-section, the shear force diagram has been plotted. Determine the maximum shear stress in section e-e of the beam. (A Note: the natural axis is located 65 mm above the toe of the cross-section and I = 5.8133×106 mm4) 160 mm |180 kN 20 mm - N.A B 100 mm 65 mm 500 mm 500 mm 30 mm 30 mm 20 mm V 90 kN Cross-section of the beam -90 kN