Situation 3: Four plates, 10 mm thick each, are connected by 25-mm diameter rivets as shown. Assume that the force will be equally distributed among the rivets. Take note that each hole diameter is 3 mm wider than the rivet diameter. A. How much punching force is required P to create a hole in a single plate? Round your answer by 5 kN. B. What is the maximum allowable force P that can be applied on the middle 100 mm plates considering the given allowable stresses? (kN) C. If P = 10 kN, what is the normal stress Allowable stresses: Bearing stress of each plate: 20 MPa Shearing stress of each rivet: 15 MPa Shearing stress of each plate: 12 MPa of the top plate at section a-a? (MPa) -O

Situation 3: Four plates, 10 mm thick each, are connected by 25-mm diameter rivets as shown. Assume that the force will be equally distributed among the rivets. Take note that each hole diameter is 3 mm wider than the rivet diameter. A. How much punching force is required P to create a hole in a single plate? Round your answer by 5 kN. B. What is the maximum allowable force P that can be applied on the middle 100 mm plates considering the given allowable stresses? (kN) C. If P = 10 kN, what is the normal stress Allowable stresses: Bearing stress of each plate: 20 MPa Shearing stress of each rivet: 15 MPa Shearing stress of each plate: 12 MPa of the top plate at section a-a? (MPa) -O

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer E and F with solutions
I will be selling a Summer Camp Innovative Sleeping System (SCISS) that suspends beds from the ceiling to make cleaning the floor easier (and to avoid snakes, bugs, and rodents). The top post is a 4-foot long steel post with a 2.5 inch x 2.5 inch cross section. The bottom post is a 3-foot long aluminum post with a 2 inch x 2 inch cross section. (a) What is the displacement of point “C" for the loading shown? (b) Has the yield stress of either post been exceeded? (c) What is the displacement of point “C” if the 120 lb loads are put on the top beds, and the 180 lb loads are put on the bottom beds? (d) For the loading in part (c), has the yield stress of either post been exceeded? 180 lb 120 lb -A- Steel Aluminum O 180 lb 120 lb
The bar is made from welding two uniform 40 lb bars together. Calculate the magnitude of the pin force at A. Express in pounds and use three significant figures. 8" 24" B 32" A
Solve for the magnitude of the vertical and horizontal forces on each joint using all the possible methods.
Answer #2 and use AREA METHOD only. Thank you so much!
The bar in the attached picture has a thickness of 16mm and a total width of 48mm. The pin has an diameter of 11mm.....
F. SHOW THE COMPLETE SOLUTION
The maximum force in a rivet in a riveting group under eccentric loading lies Nearest to the c.g of the rivet group Nearest to the load line Farthest a was from the load line At the c.g of the rivet group
Shear force is unbalanced to the left or right of the section. Select one: a. Horizontal force O b. Inclined force O c. Vertical force d. Parallel force
1.A 3inch by 3inch square steel guardrail post was hit by a car on one of its side and applieda 1.6 kN force. The base of the post is a ¼ inch thick square steel plate and is supported by four pieces half inch diameter bolts. (1 inch = 25.4 mm) a.Assuming that the bolts received an equally distributed force, what is the shear stress applied to a single bolt? b.If the bottomplate of the post is a steel with astress capacity of 120 MPa, what is the maximum allowable bearing force on the plate? c.Assuming that the post is a solid steel and was hit by a falling solid heavy object from above, what is the maximum load that it can carry? d.If the post is a steel tube withcircular hollow section and an outerdimension of 4 inch by 4 inch, what is the maximum inner diameterif same force was applied?
Fill in all blanks before submission. Round the answer to the nearest integer The figure shows a rod of length 6 ft and weight 100 lb hinged to the ground at point A. The rod rests on a stone in the shape of a sphere of radius 3ft. The center of the sphere O is located at a distance of 5 ft from point A. The normal reaction N between the sphere and the rod is lb. The horizontal component of the reaction at A is lb while the vertical component of the reaction at A is lb. 6 ft The magnitude of the reaction at A is lb. The angle of the reaction at A is 3 ft 0 5 ft
An L-shaped section has the following dimensions: The length of the longer leg is 5 in, the length of the shorter leg is 31/2., and the thickness of each leg is 3/8 in. The distance y from the back of the shorter leg to the neutral axis XX is A. 1.76 in B. 1.98 in C.1.53 in D. 1.61 in