ANSWER THE PROBLEM QUESTION AND SHOW YOUR SOLUTION CLEARLY AND BOX THE FINAL ANSWER. USE 2 DECIMAL PLACES A simply supported wood beam of length L = 10 ft carries a concentrated load P at midspan, as shown. The cross-sectional dimensionsof the beam are b = 4 in. and h = 6 in. If the allowable shear strength of the wood is 125 psi, determine the maximum load P that may beapplied at midspan. Neglect the effects of the beam's self-weight.yAnswer: P = iL2PBlb12LCXNbh

Answered: Image /qna-images/answer/1c3cd5dd-50ea-4972-9be4-8f6bcab84aae.jpg

simply supported wood beam of length L = 10 ft carries a concentrated load P at midspan, as shown. The cross-sectional dimensions the beam are b = 4 in. and h = 6 in. If the allowable shear strength of the wood is 125 psi, determine the maximum load P that may be plied at midspan. Neglect the effects of the beam's self-weight. nswer: P = i 11/13 2 P B lb 1/15- X N b h

simply supported wood beam of length L = 10 ft carries a concentrated load P at midspan, as shown. The cross-sectional dimensions the beam are b = 4 in. and h = 6 in. If the allowable shear strength of the wood is 125 psi, determine the maximum load P that may be plied at midspan. Neglect the effects of the beam's self-weight. nswer: P = i 11/13 2 P B lb 1/15- X N b h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the minimum dimension b to the nearest mm of the beam’s cross section to safely support the load. The wood has an allowable normal stress of 12 MPa and an allowable shear stress of 1.5 MPa
A 5 ft. long laminated wood beam is built up by gluing together three 2” x 6” boards to form asolid beam 6” x 6” cross section, as shown in the figure. Calculate the maximum allowable valueof P (lb.) such that both the (1) allowable shear stress in the glued joints of 100 psi and the (2)allowable bending stress of 1200 psi is not exceeded. (Disregard the weight of the beam).[Formula: Bending Stress:  = (M)(y)/I; max = (M)(c)/I; Transverse Shear Stress:  =(V)(Q)/(I*t); max = (V)(QNA)/(I*tNA)]
Determine the minimum dimension a to the nearestmm of the beam's cross section to safely support the load.The wood has an allowable normal stress of u(allow) = 10 MPaand an allowable shear stress of T(allow) = 1 MPa.
A uniformly distributed load, W1, is applied all throughout the length of the beam and a concentrated load P1 is located at the midspan of the beam. The maximum flexural stress of the wood used in the design of the beam is 20 MPa. Determine the minimum height "h" of the cross- section of the beam. P1, kN L1=L2, L3, m WI, |kN/m SET b, mm h, mm В 2.75 15 1.0 2.0 120 L1 1. L2 L3
Determine the minimum dimension a to the nearest mm of the beam's cross section safely support the load.The wood has an allowable normal stress of 10 MPa and an allowable shear stress of 1 MPa.
A beam cast monolithically has the following properties: bf=1200mm, t or hf = 110mm, bw=380mm and h=800mm. It is reinforced with 10D32mm grade 420MPa bars. Concrete strength is assumed to be 27.5MPa and the centroid of tension reinforcement is located 665mm from the outermost compression fiber. A. Determine maximum nominal moment to ensure tension controlled, kN-m. B. Calculate the balanced steel area, mm2. C. Calculate the balanced moment in kN-m.
Q2. The joint connection shown in Figure Q2 is subjected to a medium term tensile load under service class C24. The joint comprises of six 3mm diameter x 150mm long wire nails. If the characteristic density of the timber is 340kg/m³, determine the load carrying capacity P1 and P2 of the connection and slip per nail P2 P 45 mm thick Figure Q2 75 mm thick P1 P1 P 100 mm thick
The nails are on both sides of the beam and each can resist a shear of 3 KN. In addition to the distríbuted loading, determine the maximum load P that can be applied to the end of the beam. The nails are spaced 200 mm apart and the allowable shear stress for the wood is Tallow4MPa. 3.Om 300m 30m 300mat Bomm
A compression bar having a square crosssection with sides b 5 50 mm is subjected to load P.The bar is constructed from two pieces of wood thatare connected by a glued joint along plane pq thatis inclined at angle a 5 8 35 . The allowable stress inthe wood in compression is 11.5 MPa and in shear is4.5 MPa. Also, the allowable stress in the glued jointin compression is 3.5 MPa and in shear is 1.25 MPa.Determine the maximum load P that can be appliedto the bar.
For the given wooden beam, determine: a) the maximum shear stress in the wood. Vmax=3530.8 N, Iz=287239583.3 mm4 Answer: 0.2017MPa
shear strength value is in wood parallel to the grain O a. medium b. Maximun C. least O d. Greatest
A steel bar is attached to a wood support beam with four 22 mm diameter lag screws, as shown in the figure. The steel bar is 69-mm-wide by 8-mm-thick. For the steel bar, the yield strength is 235 MPa and the ultimate bearing strength is 350 MPa. The ultimate shear strength of the lag screws is 155 MPa. Factors of safety of 1.70 with respect to yield strength and 3.0 with respect to bearing strength are required for the bar. A factor of safety of 2.9 with respect to the ultimate shear strength is required for the lag screws. Determine the allowable load P that can be supported by this connection. (Note: Consider only the gross cross-sectional area of the bar-not the net area.) Support beam Answer: Pallow= 0000 P Steel bar KN