simple heat exchanger is constructed from two 1/2-in Schedule 40 steel pipes connected to a close return bend as shown in the figure below.  Calculate the pressure difference between the inlet and outlet for water flowing at 12.0 gal/min.  Report your result in psi.

Q: 5. Kerosene (sp.gr. = 0.88 ) enters the cylindrical arrangement as shown on the figure at section 1…

A: Given data: Calculate the density of kerosene as follows:

Q: Item#3 The oil tank for the hydraulic system of figure below is air-pressurized at 10psig. The inlet…

A: Bernoulli's principle asserts that the entire mechanical energy of a moving fluid, which includes…

Q: The sketch for the warm water heating system of a studio apartment is shown in the figure. The…

A: Given : The volumetric flow rate through the piping system = 0.000162 m3/s The different losses are…

Q: A shell and tube heat exchanger has the cross-section shown below. Crude oil (specific gravity, sg =…

A: To Calculate : 1). Hydraulic Diameter in mm. 2). Reynolds number of Crude oil. 3). The flow regime.…

Q: Water at 15'C (p = 1000 kg/m' and u = 1.15 x 10 kg/m s) flows from a tank through a 15 m length of…

A: Given data : Diameter of pipe = 77.9 mm = 77.9 x 10-3 m Volume flow rate = 0.03 m3/s Therefore ,…

Q: Design a pipe system to supply water at 20° C from the elevated tank to the demand point at the…

A:

Q: Calculate the frictional pressure drop in pascal for olive oil at 293 K flowing through a commercial…

A:

Q: The Figure shown below is a parallel pipeline system with two branches used to supply lubricating…

A: Given data as per the question P1=398.1 kpaP2=300 kpak1=5k2=12AA=AB=1.5×10−4 m2

Q: A simple heat exchanger is made by installing a close return bend on two 3/4-in Schedule 40 steel…

A: Given data as per the question Diameter of pipe =0.75 in =0.0625 ft Flow rate =29.2 gal/min we know…

Q: Find the air flow rate in the duct. Data: Air pressure: 17 psia air temperature at the inlet: 65 F…

A: An air channel warmer has various warming components that are either curls or cylinders that are…

Q: Problem 1: Fresh water at a temperature of 10°C flows at a rate of 0.10 m3/sec through the piping…

A: Since you have asked a multi-part question which contain more than 3 sub-parts, thus we can provide…

Q: 3: Calculate the pressure and velocity at points 2 and 3 for the water pipe shown in Figure D, = 14…

A:

Q: Mechanical-Energy Balance and Friction Losses. Hot water is being discharged from a storage tank at…

A:

Q: Water enters a pump through a 250 mm diameter pipe at 35 kPa. It leaves the pump at 140 kPa through…

A:

Q: As shown in the figure, the water flows from the ground floor of a three-storey house to the second…

A:

Q: Derive an expression for the maximum velocity for circular pipe and fixed parallel plates.

A:

Q: An open test tube at 293 K is Water at 20°C is being pumped from a tank to an elevated tank at the…

A: Given dataFlow rate of water = 5 x 10-3 m3/sPipe diameter = 4 inch = 101.6 mm = 0.1016 mPump…

Q: In Figure 7, oil with a specific gravity (s.g.) of 0.852 is to be forced from Tank A to Reservoir B…

A: Given: The specific gravity of oil, SG1 = 0.852 The total length of pipe, L = 38 m The diameter of…

Q: Compute the resulting pressure in kPa after a "real" diffuser in which the energy loss due to sudden…

A: In this problem water is flowing from the pipe and pipe has enlarging section. Now in this case…

Q: (b) A cast iron piping system deliver water at 20°C from a close tank, T1 to an open tank, T2 as…

A:

Q: As shown in the figure, a pipe system having a total length of 102 m carries a discharge of 0.060 m3…

A:

Q: Medium lubricating oil (sg=0.85) is pumped through 360m of horizontal 75mm pipe  at the rate of…

A:

Q: A pipe of 180mm bore is delivering water at a rate of 8250dm3/min at a pressure 800kN/m2. It…

A: The volume flow rate remains constant for incompressible flow in a pipe flow. This is due to the…

Q: In the figure shown, it is desired to pump 40 L/s of water from a natural stream to a small…

A: INTRODUCTION: When water flows through the pipe, the head loss is inevitable. Minor and significant…

Q: A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling…

A: Given: The flow rate, Q = 400 gal/min The pipe type = schedule 40

Q: 09. Water is supplied at 150 ft/s and 60 psi to a hydraulic turbine through a 3-ft inside diameter…

A: The power loss from inlet to exit of turbine is required to be calculated. The power loss is the…

Q: Your second customer wants to determine the required electrical power, which will be used to pump…

A:

Q: Oil is flowing at the rate of 3.14 cfs in a pipe of varying cross section. At section A, the…

A: Given data: Oil flow rate = 3.14 cfsSection A diameter = 6 inch = 0.5 ftPressure at A  = 12 Psi = 12…

Q: Two pipes 1 and 2 having the following properties are connected in series: Pipe 1 - Length = 1500m,…

A:

Q: Water at room temperature with a mass flow rate of 2 kg / s flows through a system of 2 pipes…

A:

Q: Compute the head loss and pressure drop in 80 m of horizontal 150-mm-diameter asphalted cast-iron…

A: Given:- L=80m D=150mm v=1.83 m/s T=20℃ To find:- 1) Head loss 2) Pressure drop

Q: Each of the two circular pipes carries water at 65 °C flows at a Reynolds Number of 3.8× 10^4.…

A:

Q: The hydrostatic transmission shown in the figure, is used to move a pulley attached to the shaft of…

A: Write the given data

Q: The shower head shown in the Figure delivers water at 50°C. An orifice-type flow reducer is to be…

A:

Q: A pitot tube with dia of 3cm is installed in a pipe with ID150 mm. Water flows through the pipe, and…

A:

Q: The present pumping rate of crude oil through the Alaska Pipeline with an ID of 39 in is 550,000…

A: Solution:

Q: Water is pumped through 750 ft of 6-inch nominal diameter Schedule number 40 pipe. The difference in…

A:

Q: (c) A cast iron piping system delivers water at 20°C from the lower tank to a higher tank as shown…

A:

Q: Hot oil is pumped through a heat exchanger (see figure below) at a flow rate of 0.5 L/s. An inlet…

A: The calculation for friction factor for Laminar flow:

Q: Hot oil is pumped through a heat exchanger (see figure below) at a flow rate of 0.5 L/s. An inlet…

A:

Q: Problem 2: A typical triangular heat exchanger is shown in the figure below. Considering an…

A: The above question can be solved easily by applying the Darcy-Weisbach equation is given below-…

Q: As shown in the figure, the water flows from the ground floor of a three-storey house to the second…

A: Write down the given values along with suitable variables.

Q: Twenty gpm of 60°F water enters the parallel piping system shown in the figure. Branch A consists of…

A:

Q: Calculate the power delivered by the oil to the fluid motor shown in the following figure if the…

A:

Q: Water at 15°C is transported from a large open tank to the bottom of another open tank above. The…

A: Answer: The Reynolds number of the flow: Re = 12438705.2

Q: The diagram shown illustrates the flow in a circular metal duct 20 feet long. The duct has a sudden…

A:

Q: In the figure shown, the inside diameters of the pipe at sections 1 and 2 are 250mm and 500mm,…

A: Mass flow rate is density × area × velocity  Density  = (unit weight) /(g)  Density =…

Q: Estimate the entrance length for motor oil for the following two cases

A:

Q: If water at 180°F is flowing with a velocity of 4.50 ft/s in a standard 6-in Schedule 40 pipe,…

A: calculate the weight flow rate

Heat Exchangers

Heat exchangers are the types of equipment that are primarily employed to transfer the thermal energy from one fluid to another, provided that one of the fluids should be at a higher thermal energy content than the other fluid.

Heat Exchanger

The heat exchanger is a combination of two words ''Heat'' and ''Exchanger''. It is a mechanical device that is used to exchange heat energy between two fluids.