Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in. Bar c=0.80 in. Bar d= 1.6 in. b-4.0 in. Rivets Te = 6.0 in.

Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in. Bar c=0.80 in. Bar d= 1.6 in. b-4.0 in. Rivets Te = 6.0 in.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
A composite beam is made of two brass [E = 106 GPa] plates bonded to an aluminum [E = 60 GPa] bar, as shown. The beam is subjected to a bending moment of 1720 N-m acting about the z axis. Assume b=45 mm, d₁-53 mm, d₂-13 mm. Determine: (a) the maximum bending stresses Obr, Gal in the brass plates and the aluminum bar. (b) the stress in the brass Obrj at the joints where the two materials are bonded together. Brass (2) Aluminum (1) Brass (2) b ↓ d₂ d₁ d₂
A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positions indicated. 3 m 2.5 m C 1200 kN 900 kN 80mmØ 100mmØ E = 83 GPa Bronze E = 200 GPa Steel Which of the following most nearly gives the deformation of C? a. -0.7855 mm О Ъ. +0.8575 mm c. +0.7855 mm o d. - о.8575 mm
A composite beam is made of two brass [E = 99 GPa] plates bonded to an aluminum [E = 72 GPa] bar, as shown. The beam is subjected to a bending moment of 2010 N-m acting about the z axis. Assume b-44 mm, d₁-37 mm, d₂-11 mm. Determine: (a) the maximum bending stresses Obr, al in the brass plates and the aluminum bar. (b) the stress in the brass brj at the joints where the two materials are bonded together. Brass (2) Aluminum (1) Brass (2) Answers: (a) Obr = (b) Obrj = i b d₂ d₁ MPa, oal = MPa. MPa.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN. 0.8m 0.4m B 5KN 0.6m Al 20KN Q2 5) What is the deformation 8, in mm? A=800 mm? A=1,200 mm?
The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. Determine the displacement of end A with respect to end D and the normal stress in each section. The cross-sectional area and modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C. Aluminum Eal = 10(10³) ksi AAB=0.09 in² 2.00 kip -18 in- Copper Steel Ecu=18(10³) ksi Est = 29(10³) ksi ABC = 0.12 in² ACD= 0.06 in² 3.50 kip HK 3.50 kip -12 in.- 1.75 kip 1.75 kip -16 in 1.50 kip
For the state of stress shown, determine (a) the principal stresses, (b) the maximum in-shear stress. Sketch such stresses in a two- element format. 60 MPa 90 MPa Lx 30 MPa
GIVEN: Solid alumınum bar shown: 4 in. by4 in. E = 10 x 10° psi oy = 36 ksi 4000 2000 1b 4000 16 B 12' REQ’D: A) Load in each section of the bar (state whether C or T) PAB = Pac PCD = B) Maximum axial stress in the bar. In which section does this occur? C) Final length of the bar
The beam shown left below has the cross section shown right below. Determine(a)The maximum tensile fiber stress in the beam.(b)The maximum compressive fiber stress in the beam.(c)The shearing stress 50 mm below the top surface of the flange.(d) The maximum shearing stress
! Required information A steel bar (Es= 210 GPa) and an aluminum bar (Ea = 70 GPa) are bonded together to form the composite bar shown. 8 mm 8 mm 8 mm Aluminum 24 mm -Steel Determine the maximum stress in steel when the bar is bent about a horizontal axis, with M= 56 N.m. The maximum stress in steel is - MPa.