Select sections for the conditions described, using Fy=50 ksi (345 MPa) and Fu = 65 ksi (448 MPa), unless otherwise noted. Use LRFD and ASD design expressions and show your complete solution. Select an alternative section if none of the specified section is adequate. Select the lightest S section that will safely support the service tensile loads D = 92 kips and L = 56 kips. The member is to be 20 ft long and is assumed to have one line of holes for ¾-in diameter bolts in each flange. Assume that there are at least three holes in each line 4 inches on center. Use A36 steel. Please show COMPLETE solution

Select sections for the conditions described, using Fy=50 ksi (345 MPa) and Fu = 65 ksi (448 MPa), unless otherwise noted. Use LRFD and ASD design expressions and show your complete solution. Select an alternative section if none of the specified section is adequate. Select the lightest S section that will safely support the service tensile loads D = 92 kips and L = 56 kips. The member is to be 20 ft long and is assumed to have one line of holes for ¾-in diameter bolts in each flange. Assume that there are at least three holes in each line 4 inches on center. Use A36 steel. Please show COMPLETE solution

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.3P

See similar textbooks

Related questions

Q: Suppose you are a group of cadet engineers given by your department manager a "simple" task of…

A: The given data is shown below: Nominal diameter=6 inchesSchedule number=40Material of…

Q: A granular soil is subjected to a minor principal stress of 200 kN/m2. If the angle of internal…

Q: The beam, as shown below, is loaded with a uniform moving live load of 15 kN/m. A B 1m- 2 m 3 m 2 m…

Q: Determine the maximum shear (v) and moment(m) of the beam. And sketch the shear force and bending…

Q: A cylindrical sample of soil having a cohesion of 80 kN/m2 and an angle of internal friction of 20°…

Q: ual tangent vertical curve is intended to connect grades of -3.5% and 3.8%. If th speed limit of…

Q: a smooth spacer DE. Determine the reactions at the smooth supports A and F, and also find the force…

A: Both are different questions. So I have solved only one question.

Q: A collimation error of 0.00005 ft/ ft is used in leveling a line that has a sum of 1425 ft for the…

Q: For a normally consolidated insensitive clay ∅_CD = 30°. Deviator stress at failure of the same soil…

Q: 1814 12kN/m TIENCY ·1.20m7 0.75m 0.75mm 1.20mt Determine the value of reaction at point B.

A: Fy=0VA+VB=18+12×1.22VA+VB=25.2

Q: • Determine the SLOPE AND DISPLACEMENT at point A. TAKE E = I1 GPA. THE VALUE OF "I" CAN BE SOLVED…

Q: Asap thank you. a. Ordinate of the influence line of RC at point D b. Ordinate of the influence line…

Q: The channel consists of an unfinished concrete section (f = 0.038) and overflow regions on each side…

A: Given: Channel Slope = 0.0015, fconcrete = 0.038, fbrush = 0.050

Q: Answers: 30 kul 375 KN.m/ A 11.25 KN V₂ = 11.25 KN (1) VA = 11.25 KN (↓) 30 KN (<) HA M4 = 30 KN…

A: Degree of static indeterminacy (DSI) DSI = R - r = (3+1) - 3 = 1 Let take VD (vertical reaction at…

Q: Mpa. Use normal weight of concrete. Use 40 mm clear cover ups and 25 mm main bars. Thickness of the…

A: Data given Vu= 223 KNTu =40 kN-m fc' =20.7fy =415 MPa fyt =275 MPa

Q: Problem 3. Object B weighs 100 lb. The brown cable that passes over pulley D and around pulley C…

A: This question is related to the Engineering Mechanics.

Q: loading loading M = 33 kNm at 1.5 m from en e bending moment at a section from out your answer as a…

Q: An embankment consists of clay fill for which c=25 kPa and angle of internal friction is 260 (from…

Q: Situation 12: A single plate 200 mm x 12 mm plate is connected to a steel plate by four 22 mm…

A: Block shear strength The Block shear failure is a limit state that occurs when tension failure…

Q: Q1:360 liters per second of water is flowing in a pipe. The pipe is bent by 120°.The pipe bend…

Q: The cross-section notes shown below are for a ground excavation for a 12m wide roadway. STA 12+2800…

Q: Solve each problem using the method of least work.

Q: A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The…

Q: What methods could be used to estimate river discharge for an accessible site and for a completely…

A: The Various methods used for the measurement of river discharge are : Volumetric gauging Float…

Q: Determine the bending stress along the x-axis of the W section. Determine the bending stress along…

Q: The T-intersection has 1,746 collision incidents over the last three years. Determine the accident…

Q: 4. A force of 540N is directed from C towards E in the cube. a. Determine the moment about the…

Q: P7.17. Compute the slope and deflection under the 32-kip load at B and D. Reactions are given. I =…

Q: A soil has an unconfined compressive strength of 120 kN/m2. In a triaxial compression test a…

A: Solution-The given values are as folows,Unconfined chamber strength=120kN/m2Chamber…

Q: A clay stratum is 4.5 m thick and rests on a rock surface. The coefficient of consolidation of a…

Q: consolidated

Q: A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The…

Q: 150 x 250 mm rectangle beam carries a uniform distributed load of W kN/m over its entire span. The…

Q: The homogeneous 860-kg bar AB is supported by a ball-and-socket joint at A and two cables attached…

A: 1.Redraw the figure to show the forces and points

Q: A 2.5 cm thick sample of clay was taken from the field for predicting the time of settlement for a…

Q: Q-2: Use the method of consistent deformations to analyze the beam shown in Fig. 2. And draw the…

Q: If the water surface elevation in reservoir B is 110m, what must be the water surface elevation in…

Q: Design a one way slab to carry a live load of 4500Pa and a dead load of 3525Pa. The slab has a…

Q: A mmmmm B 5.0m C "b" D 3.0m E "2" F

Q: 5. The runoff data for a river during a year along with the probable demands are given below. a. Can…

A: Part A Since the Sum of total river flow data is greater than the sum of the demands so the demands…

Q: The truncated cone shown has 8 = 60°. How long does it take to draw the liquid surface down from h =…

Q: A normally consolidated soil was subjected to tri-axial test with the following data: cell pressure=…

Q: The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly…

Q: A stratum of normally consolidated clay of thickness 10 ft is drained on one side only. It has a…

Q: 4. Which is nearest to the sun Earth or Pluto? 5. Is rock cycle in the nature opened or closed? 6.…

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Example 10.6 An embankment is to be formed with its centre line on the surface (in the form of a…

A: given that width (b)=40ft depth (d1)=10ft (d2)=20ft…

Q: consolidated drained tri-axial test was conducted on normally consolidated clay. The results were:…

Q: - Determine elongation of conical tapered bar applied load P on circular faces

A: To find: Elongation in conical tapered bar with load P on circular faces Since load applied is on…

Q: An equal tangent vertical curve is intended to connect grades of 0.9% and -2.8%. If this curve is to…

Q: Design the spacing of 12mm diameter rebars along the short direction (midspan) of a 4m x 5m and…

A: Given: 12 mm dia bars 4mX5m slab design along short direction 150 mm thickness DL = 4 kPa, LL = 4.8…

Concept explainers

Introduction to Steel Design

The area of steel design is majorly concerned with the structural engineering domain, which is a specialization of civil engineering. Steel design is often known as structural steel design, whose primary concern is to design steel structures. The primary structure involves the designing and construction of frames using structural steel as the material. Residential buildings, houses, bridges, complexes, tall buildings, industrial warehouses, aircraft frames, frames of ships, and stadiums are some of the examples of structures that use steel framing.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Trending now

This is a popular solution!

Step by step

Solved in 10 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem2. The compression member is shown in figure. Find the following: a. The Euler stress Fe. b. The buckling stress Fcr c. The design strength d. The allowable strength e. Does the member satisfactorily meet the design requirements? Why? HSS 8x 8x4 ASTM AS00, Grade B steel (Fy = 46 ksi) 15'
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The bracket is subject to an eccentric load of 150 kN. Use LRFD. Use A36 steel. Questions a) Determine the critical force on the most stressed bolt. b) Determine the nominal shear stress of the most stressed bolt.
7 7a 7b 7c Alaterally supported beam was designed for flexure. The beam is safe for shear & deflection. The most economical section is structural tubing however the said section is not readily available at the time of the construction. If you are the engineer in charge of the construction what alternative section will be the best replacement? Why? The section is 8" x 8" x 7.94 mm thick: Use Fy=248 MPa: E=200,000 MPa AISC wall thickness Ix 106 S x 103 Jx 103 mm4 mm3 mm4 rx =ry Area Ag (mm2) mm Designation Weight/m 8x8 7.94 47.36 6,039 79.25 37.84 371.99 60.35 expla'n briefly your cho'ce. (transform your comparative analys's 'nto a narative form to support your cho'ce) 8x8 14.29 80.61 10,258 76.2 59.52 585.02 99.06 8x8 72.7 9,290 76.96 54.53 539.13 90.32 8x8 9.53 56.09 7,161 78.48 44.12 432.62 70.76 mm 12.7 Zx 103 mm3 437.53 714.48 650.57 512.92
The eye bolt, shown in the figure on the right, is used to support the load of 25 kN. The allowable shear stress for the supporting material with the height "h" is 35 MPa. a) Draw the necessary FBD diagrams. b) Choose one of the steel material for the bolt and state its tensile strength and yield strength. 25mm- 25 KN
The given angle bar L125x75x12 with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm diameter bolts as shown in the figure. Using A36 steel with Fy = 248 MPa and Fu = 400 MPa, determine the following: 2. Determine the nominal tensile strength of the 12 mm thick, A36 angle bar shown based on: a. Gross yielding b. Tensile rupture Bolts used for the connection are 20 mm in diameter. O O O O O O O Effective net area of the tension member if the shear lag factor is 0.80. Select the correct response: 1,516.1 1,354.4 1,431.2 1,221.6
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis
4. Calculate the design strength (ocPn) of W24X76 with length of 12 ft. and pinned ends. A572 Grade50 steel is used. E=29x103 ksi. Show your work in detail. ASTM Classification A36 A572 Grade 50 A992 Grade 50 A500 Grade B (HSS rect, sq) A500 Grade B (HSS round) A53 Grade B Yield Strength F, (ksi) 36 50 50 46 42 35 Ultimate Strength F (ksi) 58 65 65 58 58 60
For the column shown what is the nominal compressive strength (Pn) ? Pn=? W12x50 10 12X50 THT X combilevered WI
TENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY FOUR 16 mm DIAMETER RIVETS AS SHOWN IN THE FIGURE. THE RIVETS USED ARE A502 GRADE 2, HOT DRIVEN RIVETS. THE STEEL IS ASTM A36 WITH Fy = 248 MPa AND Fu = 400 MPa. DETERMINE THE VALUE OF P. a. P BASED ON TENSION OF GROSS AREA b. P BASED ON TENSION OF NET AREA c. P BASED ON BEARING OF PROJECTED AREA d. P BASED ON SHEAR RUPTURE (BLOCK SHEAR)
ASSIGNMENT #5 BIAXIAL BENDING Problem: Check the beam shown for compliance with the NSCP Specification. Lateral support is provided only at the ends, and A992 steel is used, F, = 345 mPa. The 90 kN service loads are 30% dead load and 70% live load. a. Use LRFD b. Use ASD d tw by ty 1x(106) S(10³) mm mm mm mm³ mm mmª W410x100 415 10 260 16.9 398 1920 SECTION Tx mm 177 1m 90 kN 90 KN 1.5m W410x100 I Loaded Section Ly(106) Sy(10³) Ty mmª mm³ mm 49.5 381 62.4 1m Zx(10³) Zy(10³) mm³ mm³ 2130 581
2) Find the axial stresses of menbers FD, GD, GE State if it is tensile or Compressive. 4M 3M A LE 3m G 20 RN Go KN
Situation 2. Two plates each with thicknessF16mm are bolted together with6 -22mm dimater bolts forming a lap conne ction. Bolt spacing are as follows: S1 = 40mm, S2 = 80mm, Sa = 100mm. Bolt hole diameter=25 mm 50 250mm 30 30 60 75 Allowable stress: Tensile stess on gross area of the plate=0.60 Fy Tensile stress on net area of the plate=0.5Fy Shear Stress of the bolt Fv=120MPA Bearing Stress of the bot Fp=1.2 Fu Calculate the permiss ible tensile load P under the following Conditions: 4. Based on shear capacity of bolts 5. Based on bearing capacity of bolts 6. Based on block shear strength (taking into consideration the failure path given in the figure below) 40 80 16 mm 40 180 mm 40 Bearing Failure Path #1 140 209 Bearing Failure Path #2