Select a car automatic speed (cruising speed) control system as a process. The overall controlling process hava a fuel control unit/valve, controller, and other instruments to act as an automatic feed back speed control system. Draw a complete block diagaram for this specific speed control proces, name the components and explain the process briefly.

Select a car automatic speed (cruising speed) control system as a process. The overall controlling process hava a fuel control unit/valve, controller, and other instruments to act as an automatic feed back speed control system. Draw a complete block diagaram for this specific speed control proces, name the components and explain the process briefly.

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter39: Programming A Programmable Logic Controller

Section: Chapter Questions

Problem 8RQ: When programming in Boolean, what statement should be used to connect components in series?

See similar textbooks

Similar questions

A valve (sometimes called a swirl flap or tumbler valve) is locat The throttle opening is electronically controlled; the position of When the throttle is fully open, there's a more efficient air suppl Find the following components in the illustration: air filter air temperature sensor e intake manifold (tumbler) valve • mass air flow sensor e throttle control module (TCM)
Provide the allocation List Draw the Grafcet and obtain the grafcet equation Develop the ladder programming from the grafcet III. Description of the cycle: When the start push button is pressed the box motor conveyer is turned on until the box reaches the sensor for box. With box in position, the apple motor conveyor is turned ON and the number of apples is counted using an apple sensor. When the apple count value is 10, turn off the apple conveyor motor. Turn on the box conveyor again to move the box and when the next box arrives in the position then reset the apple counter. A schematic sketch of the automation system is provided in figure 1. apple motor conveyor Sensor for apples box motor conveyor II. I. Sensor for box CONTROL PANEL START STOP
NVIDIA GEFORCE GTX (intel) CORE I7 Bth Gen Chapter 19 Applying Pneumatic Power 475 Valve B Valve C Extension pilot Retraction pilot Valve A Goodheart-Willcox Publisher Figure 19-11. Automatic cylinder reciprocation is possible with this circult The cylinter continuously extends and retracts as long as the system is pressurized and valve A is activated. cylinder continues to extend until the ramp depresses the activation mechanism on Valve C. When Valve C is shifted, air is directed to the Retraction pilot of the four-way directional control valve. The pilot shifts the valve to direct air to the rod end of the cylinder. The cylinder begins to retract. The ramp moves off Valve C, which allows the Retraction pilot line to vent. The cylinder continues to retract until the ramp depresses the activation mechanism on Valve B This allows system air pressure to again activate the Extension pilot, beginning another sequence. The cylin- der continues to reciprocate as long as Valve A is held in…
graphical Make and method. 0₂ 92 Bas E D-M make End < Efpector parameter Final table of HTM the manipulator
III.Question and Answer 1.Understand the given Physical process control diagram and explain the working of the system. Actual level Reference Controller Measurement level System H Pump Tank Liquid Level Control System Electronics Coach 2. Understand the given Industrial process control system and convert it in to Block diagram (draw neatly) 4-20 mA signal FC 4-20 mA signal FY FT 3-15 PSI signal FV Pump Pipe InstrumentationTools.com
This is a diagram of a domestic hot-water system. The gas valve is operated by the controller, which, in turn, is operated by the temperature measuring and comparing device. The gas valve operates the main burner in full-on/full-off modes. Hot Water Faucel (nomaly closed) Flue Gases Cold Water Pressure Reliel Valve Check Valve Temperature Measuring and Comparing Device Controller Skop Valve Gas a) Draw a simplified Fault Tree for this hot-water system b) Find the minimal cut sets c) Find the minimal path sets 华
Please provide an FBD of the given problem
Give one example of an engine management system fault for each component Air-flow meters Temperature sensors And for each of the following: (5 - 10 words each Intermittent faults Multi-system faults Introduced as a result of a system repair Indirect, caused by the influence of external systems In your answer, briefly explain the process that would be followed to diagnose the fault.
4G : 12:30 i sct.edu.om THAL LAMIVI IVIILAIUU IV y. Process Group 3 Question 13 Not yet answered Marked out of 1.00 P Flag question _ is used to give the counter turning cycle of CNC machine. O a. G96 O b. G00 C. GO1 d. G73 Previous page Next page Previous activity ( Dip. Project II
Complete the schematic below to provide for the following: 1. Cylinders extend and retract together. The cylinders extend when the valve lever is pulled ouat and retract when the lever is pushed in. 2. Provide independently adjustable meter-in flow control for extend. The flow control used to extend Cyl #1 should be labeled "FC1". The flow control used to extend Cyl #2 should be labeled "FC2". 3. Provide independently adjustable meter-out flow control for extend. retract The flow control used to retract Cyl #1 should be labeled "FC3". The flow control used to retract Cyl #2 should be labeled "FC4". CYL1 CYL #2 "AUHVA
In an industry, the water in a boiler tank needs to be kept at constant pressure, water to the tank comes at constant flow rate and steam is coming from a valve to maintain the pressure. A pressure gauge is used to measure the water pressure in the tank. a. Provide the block diagram representation using a PID controller for the above mentioned condition (Control the pressure using the proportional valve.). b. explain the working principle.
Provide datum lines and complete FBD please thanks