Seatwork: Show your complete solution. Use 4 decimal places. Thermal Stress: In the LRT II project, steel railroad rails of 20 meters long are to be installed. If lowest temperature considered is 22 ℃ and a maximum temperature of 36 ℃ is designed for, and the modulus of elasticity of steel to be 207000 MPa, determine the clearance between rails such that adjoining rail will just touch at maximum design temperature.

Seatwork: Show your complete solution. Use 4 decimal places. Thermal Stress: In the LRT II project, steel railroad rails of 20 meters long are to be installed. If lowest temperature considered is 22 ℃ and a maximum temperature of 36 ℃ is designed for, and the modulus of elasticity of steel to be 207000 MPa, determine the clearance between rails such that adjoining rail will just touch at maximum design temperature.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Similar questions

5. Find the length in feet 0f 9/16 inch diameter rope required to fill a drum having the following dimensions: B = 24 in., D = 18 in. , H = 30 in. (K = 0.741)
Find the V-X and M-X diagrams. For the value of P use 182 kips. show all steps
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 48512-Nload, using the following data: length of steel = 1.42 m, length of bronze = 2.36 m Area of steel = 639 mm, Area of bronze = 319 mm Modulus of elasticity of steel = 180 Gpa, Modulus of elasticity of bronze = 81 Gpa x = 0.58 m, y = 1.13 m, and z = 0.72 m. Round off the final answer to two decimal places.
Learning Goal: To use Mohr's circle to determine the principal stresses, the maximum in-plane shear stress, and the average normal stress in an element. The state of plane stress on an element is shown below. Let oz= 30.0 MPa, O, = -100.0 MPa, and Try = 50.0 MPa 100 MPa 50.0 MPa 30.0 MPa Part A - Construction of Mohr's circle for the state of stress For the element shown, construct Mohr's circle for the state of stress shown associated with the x plane. First, select the center of Mohr's circle (point C) and select the point that represents the state of plane stress shown (point A). Given these two points, determine the length of the line connecting these two points, which represents the radius R of the Mohr's circle.
Home / Chapter 1: Stress / M1.5: Shear Stress in Pin Support concept checkpoints Compute the resultant force acting on the pin at C (in kN). A 500.00 mm 60 kN kN 500.00 mm Enter 65 kN 500.00 mm 900.00 mm
Q1-B // A steel bar has a square section of 10 mm side and a length of 60 mm, subjected to a tension force of 50 KN, as a result the bar has extended 2 mm; Calculate: 1-Yong modulus 2- The engineering stress 3- The engineering sustain 4- The true stress 5- The true strain 6- The percentage reduction in Area
GIVEN: W= 595 N GIVEN: ANGLE A= 44 DEGREE GIVEN: ANGLE B= 14 DEGREE ANSWER: SOLVE (A) IN UNIT CM SOLVE (B) IN UNIT N-CM SOLVE (C) IN N-CM PLS SHOW COMPLETE SOLUTION AND WRITE LEGIBLY AND SHOW THE FREE BODY THE DIAGRAM PLS TAKE NOTE OF THE UNITS WHICH ARE IN CM NOT IN MM AND ALSO LOOK AT WHAT SHOULD BE THE UNITS IN SOLVING (A) IN UNIT CM IN (B) IN UNIT N-CM AND IN (C) IN N-CM.
2. A spherical stainless-steel tank having an inner diameter 'D', is used to store natural gas at a pressure of 'p'. The properties of the steel are as follows: yield stress in tension is "T'; yield stress in shear is 'S' and modulus of elasticity is 'E'. The desired factor of safety with respect to yielding is F.S'. Determine the minimum permissible thickness tmin Of the tank. D=500mm, p=19MPA,T=970MPA,S=500Mpa,E=196GPA,F.S=2.8 ww.
Problem Set – Temperature Change 1. A steel tire has a dimensions indicated in the figure below. At 78 degrees Celsius, the said tire was fit into a 1.8m to an engine wheel with 24 degrees Celsius. Calculate the contact pressure between the tire and the wheel after fitting together due to colling of 24 degrees Celsius. The coefficient of expansion due to temperature of the tire is 12.3 micrometer/ m- degrees Celsius and Modulus of Elasticity is EN GPa. | 12 mm | 200 mm 900mm wide steel tire- 12 mm Note: Neglect the deformation of the wheel due to the pressure of the tire Fn- 100
please solve step 2
The Cable in figure P1.2 has a diameter of 1/5 in. If the maximum stress in the cable must be limited to 4 ksi(T), what is the maximum weight that can be lifted? (FBD need)
An element made of AISI 1020 CD steel is shown, but to shape it, it had to be machined. It must have a reliability of 99.9999%.It is subjected to the loads P₁= 200 pounds and P₂= 400 pounds; In others, the force in the "z" direction does not act, but the force in "y" remains with the same magnitude, but is completely reversed, in the positive and negative sense of the "y". Determine:to. The critical point of the system and for this establish the state of effort. Explainb. Apply Mohr's circle to the critical stress state and obtain σ1, σ2 and tmaxC Determine the safety factor and explain.