28. A centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specificvolume is 126 and final specific volume is 3.25 If the inlet suction lirte is 4" LD. and thedischarge line is 2.5 LD. Determine[a) The change in flow energy hetween the boundaries in(b.) the mass flow rate in-and(c) the change in velocity in Ips

SA centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specific velume is 126 and final specific volume is 3.25f the inlet suction lirte is 4" LD. and the discharge line is 25"ID. Determine [a] The change in flow energy between the boundaries in- and (c) the change in velocity in Ips the mass flow rate in

SA centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specific velume is 126 and final specific volume is 3.25f the inlet suction lirte is 4" LD. and the discharge line is 25"ID. Determine [a] The change in flow energy between the boundaries in- and (c) the change in velocity in Ips the mass flow rate in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pls. Answer this..? A steam engine has 10% brake thermal efficiency and consumes 750 kg/hr steam. The enthalpy of steam at the entrance ang exit of the engine and condenser are 2800 and 450 kj/kg repectively. Determine the brake power of the engine in kw.
Ans. 3908 m/min. 14.5 Find the cylinder dimensions of a single-cylinder, double-acting compressor handling 28.32 e/revolution of air from 99.975 kPaa to 723.954 kPaa. Compression and reexpansion are in accordance with PV135 = C. Use the conventional volumetric efficiency; c = 5% and L/D = 1. %3D %3D
28. A centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specifie volume is 12.6 and final specific volume is 3.25 If the inlet suction lirfe is 4" I.D. and the discharge line is 2.5" I.D. Determine ft-lb (a.) The change in flow energy between the boundaries in- min Ib (b.) the mass flow rate in and min (c.) the change in velocity in fps.
Air with a mass flow rate of 600 kg/s is compressed at constant temperature with aninitial pressure of 720.059 mm Hg to 4650.382 mm Hg. The final volume after thecompression is 7.65 m3. Prove that:a. the a 6.465 m3 of volume was added/lost due to the compression process.b. during a non-flow process, a 1370.311 kJ/s amount of heat is transferred to thesystem.
The power output of a steam turbine is 5 MW. The inlet conditions are 2 MPa of pressure, 400 degrees * C of temperature, 50 m/s of velocity and 10 m of elevation. The exit conditions are 15 kPa, 0.9 dry quality, 180 m/s and 6 m elevation. Compute: (i) The magnitude of A h, A ke, Ape, (ii) Work done per kg of steam,
2. A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079ft/cu. ft and discharges it with a density of 0.304 lb/cu. ft. At the suction, P 1 = 15 Psia; atdischarge, P 2 = 80 psia. The increase in the specific internal energy is 33.8 BTU/lb and the heattransferred from the air by cooling is 13Btu/lb. Determine the work on the air in BTU/min and inhp. Neglect kinetic energy. 3 decimal in final answer pls
A large commercial air-conditioning unit processess 5 kg/s of atmospheric air. The air enters at a pressure of 105 KPa. Its dry-bulb temperatue of 20 °C, a wet-bulb temperatue of 10 °C, and a pressure of 100 kPa. How much water is being removed fom the air in one hour? Conver to liters/hr
Ata particular stage of a reaction turbine the mean blade speed is 140 nı/sec and the steam is at a pressure of 20 bar with temperature of 250° C. Fixed and moving blades at this stage haye inlet angles 30° and exit angles 20°. The stage efficiency is 80%. Determine (i) Specific entholpy drop across the stage in kJ/kg. (ti) Drum Dia and blade height if heigh is one-twelfth of the drum dia. and the steam flow is 120 kg/sec.
HANDWRITTEN and with given, required and solution. Engr. Darmis is tasked to design a frictionless and constant temperature steady-flow system that will be used for power generation using Nitrogen as its working fluid. The initial gage pressure is 110 pounds per square inch and the final volume is 170 cubic feet. If ninety-one pound-mass of the fluid gain 3.253 BTU/R of entropy per minute. Find the (a) initial volume, (b) temperature, and (c) Work. (d) If the heat is equal to 9940 BTU, how long did the process took place?
4. to convert the kinetic energy of water into the mechanical shaft energy. Water enters the turbine, at the inlet, with the velocity Vin = 40m/s and the mass flow rate m=1,000kg/s. Water exits the Vi,z40ms turbine with a negligible velocity, say, Vout = 0 m/s.The efficiency of m - loooly/s Figure on the right shows a hydraulic turbine designed HzO HzO the turbine is 75 %. Potential energy and flow work can be ignored. 4а. Please calculate the specific kinetic energy of water entering the turbine ( ɛr or ke; in J/kg). 4b. Please calculate the rate of total kinetic energy of the water flow ( É̟ or KĖ ; in J/s or W) 4с. Please determine the mechanical power output of this turbine (Wou; in W or kW). 4d. Please determine how much mechanical energy would this turbine generate during an hour
answer is provided and mass flow rate is 4.2 kg/sec
impact of a jet Draw the relationship of the Fact against the jet velocity Vj