SA A piston 11.96 cm diameter and 14 cm long works in a cylinder 12 diameter. A lubricating oil which fills the space between them has Viscosity 0.65 poise. Calculate the speed at which the piston will move through the cylinder when an axial load of 0.86 kg is applied. Neglect the inertia of the piston. cm

SA A piston 11.96 cm diameter and 14 cm long works in a cylinder 12 diameter. A lubricating oil which fills the space between them has Viscosity 0.65 poise. Calculate the speed at which the piston will move through the cylinder when an axial load of 0.86 kg is applied. Neglect the inertia of the piston. cm

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

find the answer Gas in enclosed cylinder with a weighted piston as the top boundary. The gas us heated and expands from a volume of 0.04 m^3 to 0.10 m^3. The pressure varies such that PV=consant, and the initial pressure is 200 kPa. Calculate the work done by the system in kiloJoules? Write the answer up to TWO DECIMAL PLACES.
Answer the following. A: When the pressure of liquid is increased from 3.5 MN/m² to 6.5 MN/m² its volume is found to decrease by (0.08) percent. What is the bulk modulus of elasticity of the liquid? B: An open cylindrical tank (1.2m) in diameter and (1.8m) deep is filled with water and rotated about its central axis at (60 r.p.m). How much liquid is spill and how deep of the water at the central axis.
In order to predict the behavior of a small oil pump, tests are to be made on a model using air. The oil pump is to be driven by a 1/20 hp motor at 1800 rpm and a ¼ hp motor is available to drive the air pump at 600 rpm. Using the SG of oil at 0.92 and the density of air constant at 0.00238 slug/ft3, what size model should be built?
2. A vertical cylindrical tank is filled to the top with water at a temperature of 20°C. The diameter of the tank is 12m and depth of 4m. If the water is heated to 50°C, how much water will spill over in m? 3 A quart of SAE 30 oil at 6goE weighse about 1 85lh. Calculate the oil's
H.W: A hypodermic syringe contains a medicine with the density of water. The barrel of the syringe has a cross-sectional area (2.50x10-5) m2, and the needle has a cross-sectional area (1.00x10 8 ) m². In the absence of a force on the plunger, the pressure everywhere is 1.00 atm. A force F of magnitude 2.00 N acts on the plunger, making medicine squirt horizontally from the needle. Determine the speed of the medicine as it leaves the needles tip.
plz help me with this one , i would appreciate it if you can help me now. A piston with a diameter of 0.8 m and width of L=0.6 m rotates with 6 rad/s inside a cylinder that has a diameter of 1 m that filled with oil that has a viscosity of 8x10-3 N.s/m2 What is the shear force that acts on the circumference of the piston (N)? Assume the variation in velocity of the oil is linear.
Q: Prediet the manometer reading after (4.45N) weight 4 is placed on the pan. Assume no leakage or friction between piston f cylinder. Pan 37.5 25mm dia. dia. oil 600 mm 5-०-92 75 2 5 mn dia-
Calculate the condition of gas in pressure = 10 bare and specific volume 175000 cm3/kg
3 A fluid of density 1200 kg/m° at 1 atm pressure is compressed to 101 atm pressure isothermally. If the isothermal compression is 4.8, 105 atm. -1 the 3. increase in density in kg/m of fluid is
Qz: A A liquid of (N = 1:25 Pais.) fills the space of (Sum) shown in figure below. Calculate the forque (T) required to rotate the frustum cone at a constant speed of a (60 rip.u). IT Smm o. 3m 0.7m
2. A 20 cm long ram has its entire length engaged in a cylinder. The diameter of the ram is 10 cm and the gap between the ram and the cylinder is 1mm which is filled with SAE 30 oil at 40°C. The ram travels at 54. Find the frictional resistance(force) of the surfaces.
The physical model of a pipe containing water with kinematic viscosity has been built in the scale of in a laboratory. Find the ratio of velocity of water in the main pipe with kinematic viscosity of to the model. Discuss the difference in the velocities of the model and main pipe.