S Electrical Engineerin.. x Lecture 13 Theveni. 287 / 2618 130% 5. P2.84. Find the Thévenin and Norton equivalent circuits for the circuit shown in Figure P2.84. Take care that you orient the polarity of the voltage source and the direction of the current source correctly relative to terminals a and b. What effect does the 7-2[8&7[dash||Ome|&] resistor have on the equivalent circuits? Explain your answer. 1 A 48 2 12 V 162 Figure P2.84

S Electrical Engineerin.. x Lecture 13 Theveni. 287 / 2618 130% 5. P2.84. Find the Thévenin and Norton equivalent circuits for the circuit shown in Figure P2.84. Take care that you orient the polarity of the voltage source and the direction of the current source correctly relative to terminals a and b. What effect does the 7-2[8&7[dash||Ome|&] resistor have on the equivalent circuits? Explain your answer. 1 A 48 2 12 V 162 Figure P2.84

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter17: Commercial And Industrial Air-conditioning Control Systems

Section: Chapter Questions

Problem 22RQ

See similar textbooks

Similar questions

C2 (i). Draw the Schematic diagram and explain the working of LVDT and write any two applications of it. .
A chopper is employed to charge a battery as shown in figure. The charging current is 5 A. The duty ratio is 0.2. The chopper output voltage is also shown in the figure. The peak to peak ripple current in the charging current is https://practicepaper.in/wp-content/uploads/GATE/EE/20031/q87.jpg
b) Use the ALU 74181 in the figure below and the tables (one is enough; second maybe, need to check the new kit) to implement : A + B, A – B, A. B. (MSB) (LSB) 10 (MSB) F3 F2 F1 FO S3 Cn+4 16 s2 20 U14 15 S1 14 so A3 A2 A1 AO B3 B2 B1 B0 M Cn 24 23 22 21 28 27 T26 25 (LSB) (MSB) (LSB)(MSB) (LSB) And given that under M = 1 the circuit performs the following arithmetic and logic functions according to Table 11.1. Input selection S3 Output M-H S2 SI Cn=L. F3 F2 F1 FO A 1 -A В -B A&B AxB 1 A'B 1 Ax(-B) (-A)xB (-A)x(-B) 1 1 ACTIVE HIGH DATA M-L: ARITHMETIC OPERATIONS SELECTION M-H LOGIC s3 s2 s1 so Ino carry) (with carry) F-A PLUS 1 F- LA + B) PLUS 1 F- (A + BI PLUS 1 FUNCTIONS L L F-A F-A+B F-AB F-A H FA+B F-A+T F- MINUS 1 12s COMPL) F-A PLUS AB F- IA + BI PLUS AB L L L L F-0 F-ZERO F- AB F-A PLUS AB PLUS 1 F- (A + BI PLUS AB PLUS 1 L L L H L F-AOB F- AB L L F-A MINUS B MINUS 1 F-A MINUS B F- AB MINUS 1 F- A F-A PLUS AB PLUS1 F-A PLUS B PLUS 1 F- IA + B PLUS AB PLUS 1 L H L F-A PLUS AB…
Q3. Draw the output voltage waveform for each circuit including the voltage values. (Ideal model) 2.2 k2 +30 V V. OV -30 V +5 V +50 V 47 3.3 kn -5 V -50 V D 2:1 +100 V -- IN4001 R. V ov 10 k2 -100 V IN4001 Q4. For the following bridge rectifier circuit, draw the output voltage waveform across the load (RL) showing the maximum value. Calculate the following: The average value of the output voltage across the load (RL). a. b. The rms value of the output voltage across the load (RL). c. The average load current. d. The rms value of the load current. (Use constant voltage drop model for the Silicon diode) 5:1 D, o Vrms DA 10 KN
Draw the circuit diagram for the experimental verification of Ohm's law
The platinum RTD has been connected to the wheatstone bridge circuit represented by R3 with Vin = 5V, R1=R2=R4 = 100 ohms. Find the temperature where the RTD is subjected if voltage reading is 0.25 volts. Vin Select one: R₂ a. 39.23 °C b. 42.47 °C c. 48.73 °C d. 51.67 °C O f. e. 57.34 °C 62.76 °C g. 68.45 °C h. 74.28 °C
Compute the convolution y[n] = x[n] *h[n] of the following pairs of signals: (d) x[n] and h[n] are as in Figure P2.21. 1012345 x[n] h[n] IIIII….…..IIIII 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Figure P2.21
1:EV * Asiacell Illı. Exercise_971Ob0ea2419c5ec80ad189723... Exercise Si E, c Si E20 o Vo R{1 kn E 10 V Design the circuit shown below using MULTISIM, the measure (current & voltage) on the resistor two times first when (El = 3v & E2 = 10v) and second when (El = 15V & E2 = 2v), analysis the circuit theoretically and compare between practical and theoretical results.
QUESTION 2 a) b) Figure Q2a shows a parallel clipper circuit. Analyze the circuit and hence sketch the output waveform for one complete cycle of the input. R own V₁ 10 Vi (V) A -20 15- -15 t(s) t(s) Figure Q2a Determine the output voltage, V, and hence sketch the output voltage waveform for the clamper circuit shown in Figure Q2b. C Figure Q2b Si Si 5 V 3V V₂ R Vo
A Wheatstone bridge is used for measuriug the valuc of change of resistance of a strain gauge wnich forms one of the arms of the bridge. All tbe arms of the bridge including the strain gauge have a resistance of 100 N each. The maximum a!lowable power dissipation from the strain gauge is 250 mW. Determine the value of maximu:n permissible current through the strain gauge and maximum allowable value of bridge supply voltage. Suppose a source of 20 V is available, lind the value of series resistance to be connected between the source and the bridge to limit the input voltage of the bridge to permissible level.
I need help with part d and part e. Please show clearly how to solve those parts. Thank you.
A. Determine V1 without C B. Determine V1 and VR with C C. From aB Determine V2, IL, PD D. From B determine the efficiency of the regulator (OUR SUBJECT IS INDUSTRIAL ELECTRONIC)