Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The di Lanath lant The alloawble stress of link BD is 200 MPa. a) Determine the maximum possible value of the load P b) If P-90 kN, determine the change in temperature needed for link BD to have no change in length. Given =12*10/C, E200 GPa B A D 0.4m 0.2m

Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The di Lanath lant The alloawble stress of link BD is 200 MPa. a) Determine the maximum possible value of the load P b) If P-90 kN, determine the change in temperature needed for link BD to have no change in length. Given =12*10/C, E200 GPa B A D 0.4m 0.2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Eiample ai ABC is loaded via a 500 N.m couple and a 600 N force as shown. Tlie The is connected to the rest of the system by a pin joint at B and a roller support at Beteune the magnitide of the reaction forces on the beam at the supports. 600 N 300 N m 400 300 500 Ans. Dimensions in mm RC=1700 N 20 RBx=1597.5 N RBy=1181.4 N Erample Determine the force Pnecded to lift the load. Alsa, determine the proper placement x of the hook for cotilibrium. Neglect the weight of the beam. 0.9 m 100 mm 100 mm 100 mm 6 kN The uniform rod of length L and weight W is supported on the simooth planes. Determine its position e for equilibrium. Neglect the thickness of the rod. Ans 6= tan
回の shear stress tmax in any of the three bars? P3 9 m P 135° up. (D 135° 90 dz s applied Knowing the steel the steel 09. A circular steel tube of length L = 0.90 m is loaded in torsion by torques T. s in the (a) If the inner radius of the tube is r, = 40 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y1 (in radians) at the inner surface? (b) If the maximum allowable shear strain is 0.0005 rad and the angle of twist is to be kept at 0.5° by adjusting the torque T, what is the maximum permissible outer radius (r2)max? B 12 mm is to be of ACR
Q2. Member ABC is supported by two fixed supports at points A and C. The member has heights of 100mm at points A and C whereas the height is 600mm at point B. A point torque of 10KN.m is applied Im away from the point A. Determine the reactions at supports A and C. Write vour results in the box below. Use G-100GPA. B A T= 10 kN.m 100 mm 600 mm 1 m 1 m 2 m
The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel wires are 1cm in diameter. If the load P is 5kN and the weight of the beam is neglected, solve the deformation at wire BD. E 4 m +2m+2m -3 m O 0.417mm O 0.497mm O 0.329mm O 0.231mm
Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that E, = 200 GPa and Es = 100 GPa, determine (a) the reactions at A and E, (b) the stress at segment BC, (c) the deflection of point D. Dimensions in mm 100 100 -180- +120– Dl E Steel B Brass 60 kN 40 kN 40-mm diam. 30-mm diam.
2. The plate is acted on by four parallel forces, three of which are shown. The fourth force P and its line of action are unknown. The resultant of this force system is the couple-vector. (-1100i + 1500J)lbft. Determine P and its line of action. %D 1400 lb 200 lb 300 1b y 2. ft 3 ft 3 ft 4 ft
An assembly of bars are designed in Figure 1. The assembly is made of structural A-36 steel where bar AB and BC has a drameter of 50 mm. ASTM and 25 mm The respectively. determine дар between C and the rigid wall at D is initially 0-15 mm, the support reaction at A and D when the force P= 292 kN is applied at B 600mm 450mm 292- A B D
Rigid bar ABC is supported by two identical solid bronze [E - 96 GPa, a = 18.2 x 10-6/°C] rods, and a solid steel [E - 210 GPa, a = 9.9 × 10-6/°C] rod. The bronze rods (1) each have a diameter of 16 mm and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 27 mm. The bars are unstressed when the structure is assembled at 22°C. Assume L = 0.3 m. When the temperature decreases to -15°C, determine: (a) the normal stresses in the bronze and steel rods o1,02 (positive if tensile, negative if compressive). (b) the normal strains in the bronze and steel rods e1, €2 (positive if stretched, negative if shortened). (1) (1) L Answers: i MPa, 02 = i MPa. i HE, E2 = i με. = I3
Rigid bar ABC is supported by two identical solid bronze [E = 111 GPa, a = 15.3 x 10-6/°C] rods, and a solid steel [E = 219 GPa, α = 11.9 × 10-6/°C] rod. The bronze rods (1) each have a diameter of 19 mm and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 18 mm. The bars are unstressed when the structure is assembled at 33°C. Assume L = 0.42 m. When the temperature decreases to -23°C, determine: (a) the normal stresses in the bronze and steel rods 6₁, 6₂ (positive if tensile, negative if compressive). (b) the normal strains in the bronze and steel rods ₁, 2 (positive if stretched, negative if shortened). (1) Answers: σ₁ = E₁ = i M. (2) B (1) L MPa, 0₂ = i με, ἔγ = i MPa. με.
SITUATION 3. In the frame shown, members ACE and BCD are connected by a pin at C and by the link DE. For the loading shown: (Concentrated load is = 480 N) 160 mm 4S0 N 60 mm 80 mm E 150 mn- 60 mm 100 mm 1. determine the reaction a B
125. A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm, respectively. An axial load of 12kN is applied on the bar. E = 2x105 N/mm2. The elongation of %3D the bar will be 1 (b) 6n 1 mm (a) mm (c) -mm (d) -mm 2
The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant Rat A. The couple is positive if counterclockwise, negative if clockwise. 2.05 KN Answers: M= I R-1 1.25 m 690 N-m 0.44 m KN-m 1+ 67" 10.14 m 0.14 m 1.16 KN 1) KN