Rigid bar ABC is supported by two aluminum alloy (E = 10,000 ksi) rods as shown below. The horizontal distance between rods (1) and (2) is a = 150 in. Rod (1) has a length of L₁ = 99 in. and a cross-sectional area of A₁ = 0.55 in.². Rod (2) has a length of L₂ = 96 in. and a cross-sectional area of A₂ = 0.95 in.². Rigid bar ABC is to remain horizontal under a load of P = 35 kips. Determine the distance x from joint A to the location of load P so that bar ABC remains horizontal.

Rigid bar ABC is supported by two aluminum alloy (E = 10,000 ksi) rods as shown below. The horizontal distance between rods (1) and (2) is a = 150 in. Rod (1) has a length of L₁ = 99 in. and a cross-sectional area of A₁ = 0.55 in.². Rod (2) has a length of L₂ = 96 in. and a cross-sectional area of A₂ = 0.95 in.². Rigid bar ABC is to remain horizontal under a load of P = 35 kips. Determine the distance x from joint A to the location of load P so that bar ABC remains horizontal.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6. Three wires are used to support the 150-lb force. The wires AB and AC are made of steel, and wire AD is made of copper. Assume that the three wires have constant cross-sectional area A = 0.0123 in?. For steel wire, a = 8 x 10 in/ (in°F ) and E = 29000 ksi and for copper wire, a = 9.6 x 10 in/ (in°F ) and E = 17000 ksi. Calculate the axial force exerted by the three wires if the temperature is raised by 80°F. Answer: Pu= 10 Ib, Pu= 136 Ib 40 in. 60 in. 45°. -45° 60 in. V150 Ib
( 48ll O O 2 9:YV The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at point B, the tube made of material with G2=230 GPa has an outer diameter 37 mm and wall thickness of 7 mm. If T1=803 N.m and T2=1445 N.m, answer the following questions: A B T2 N-m 0.4 m 0.1 m 0.3 m T1 N-m The polar moment of inertia of the rod BD is Your answer The polar moment of inertia of the tube CA is
A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a cross-sectional area of A₁ = 0.40 in.² and a length of L₁ = 120 in. Bar (2) has an area of A₂ = 0.40 in.² and a length of L₂ = 100 in. Bar (3) has an area of A3 = 0.13 in.² and a length of L3 = 35 in. The loads and angles are P = 26 kips, a = 39%, Q = 14 kips, B = 61°, and R = 12 kips. Determine the vertical deflection of end A. A downwards deflection is positive, while an upwards deflection is negative. D (1) L₁ (2) Answer: ỖA = i B A R L2 L3 in.
A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a cross-sectional area of A₁ = 0.45 in.² and a length of L₁ = 85 in. Bar (2) has an area of A₂ = 0.45 in.² and a length of L2 = 80 in. Bar (3) has an area of A3 = 0.19 in.² and a length of L3 = 40 in. The loads and angles are P = 24 kips, a = 30°, Q = 10 kips, ß = 56°, and R = 11 kips. Determine the vertical deflection of end A. P B D B A (1) (2) VR U O L₁ L2 L3
30 kN 90 kN B C 13 30 kN 400 mm 600 mm- The rod shown is made of steel (E= 200 GPa) has a cross sectional area of 1 × 10-³m². The change of length of part AB is most likely equals to: (a) -180 x 10-6 m (b) - 84 x 10-6 m (c) +96 x 10-6 m
The rods 1, 2, and 3 shown below are welded together, mounted between two rigid walls and subjected to the two forces shown at joints B and C. Rods 1 and 3 are of the same length, L= L3 = 1.0 m and rod 2 has a length L2 = 1.8 m. Rods 1 and 3 are made from a material with E - 70 GPa. Rod 2 is made from a material with E = 100 GPa. The cross sections are given by: A1 = A3 = 11x10 mm? and A2 = displacements of joints B and C. %3D 17x103 mm?. Determine the %3D (2) 200 kN (1) (3) 350 kN A B DL
Question 3: a. A mass of (Z + 50) kg is hung on a steel wire of diameter (Z + 5) mm and the extension found is (Z + 10) mm. If the Young's Modulus of the wire is 200 GPa, Calculate, i. the cross-sectional area of the fishing rope ii. the tensile strain b. A copper sheet of (Z + 75) cm width, (Z + 100) cm height, and (Z + 0.5) cm thick is acted by a shearing force of 50 × 10³ N, as shown in figure below. If the shearing Modulus of Copper is 4.2 x 101°N/m², find the followings: i. Shear Stress ii. Linear Displacement (Ax) Z=62 F Ax thick Width height
The rod has a diameter of 40 mm. (Figure 1) It is subjected to the force system F. F, = 920 N. 1350 N, F,= 540 N, Figure 1 of 1 100 mm 300mm B 100 N m
A 13-mm-diameter steel (E = 193 GPa) rod (2) is connected to a 27-mm-wide by 10-mm-thick rectangular aluminum (E = 72 GPa) bar (1), as shown. Assume L1 = 0.74 m and L2 = 1.38 m. Determine the force P (in kN rounded to the nearest tenths) required to stretch the assembly 8.1 mm.
5. If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of P. The wire is A-36 steel and has a diameter of 3 mm. (Esteel = 200 GPa) 300 mm -200 mm- B 400 mm - [Ans: P = 628 N]
Rigid bar ABCD is loaded and supported as shown. Steel [E = 30800 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.78 in.2 and bar (2) has a cross-sectional area of 0.32 in.2. After load P is applied, the strain in bar (1) is found to be 610 μεμε. Assume L1=50 in., L2=76 in., a=28 in., b=21 in., and c=22 in. Determine:(a) the stresses in bars (1) and (2).(b) the vertical deflection vD of point D on the rigid bar.(c) the load P.
Subject: Mechanical engineering. Question: A bar 1.5 m long is made up of two parts of aluminium and steel and that cross sectional area of Aluminum bar is twice that of steel bar. The rod is subjected to an axial tensile load of 200 kN. If the elongation in aluminium and steel bar are equal, find the length of the two parts of the bar. Take E steel 200GPa; E Aluminium one third of E steel.