respectively. Using a = 350 mm, b = 45 mm, c = 250 mm, L1 = 3 m, L2 = 7 m, L3 = 4 m, w1 = 38 kN/m, w2 = 18 kN/m, P = 19 kN and M = 24 kNm, determine a. The maximum flexural stresses in tension and compression. I b. The stress at a point 3 m to the left of the right support and 90 mm above the bottom. c. If wj = 1.5w2 and all concentrated load and moment are removed, determine the maximum safe value of w, and w2. I

respectively. Using a = 350 mm, b = 45 mm, c = 250 mm, L1 = 3 m, L2 = 7 m, L3 = 4 m, w1 = 38 kN/m, w2 = 18 kN/m, P = 19 kN and M = 24 kNm, determine a. The maximum flexural stresses in tension and compression. I b. The stress at a point 3 m to the left of the right support and 90 mm above the bottom. c. If wj = 1.5w2 and all concentrated load and moment are removed, determine the maximum safe value of w, and w2. I

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1/ Find max tension & compression stresses for part BC for beam shown in figure below. 20 KN 20 KN 2 cm 2 cm B 10 cm A D 2 cm 30 cm 50 cm 30 cm 10 cm Q2/ Find diagram for shear force and moment of EFGH beam as shown in figure below. 20 KN 3 A 4 400 cm 400 cm 400 cm 400 cm H 'F 400 cm B 28 KN
Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of diameter 3m from an overhead point. If the moulding weighs 5 kN/m and the attachment point is 4m above it, determine the following:a. Calculate the tension of the cable.b. Determine the diameter of the wire if the allowable stress is 125 MPa.c. If the diameter of the cable is 10 mm, find the deflection of the steel cable.d. If the diameter of the cable is 10 mm, find the vertical displacement of the molder.
3.2.2 P P Tav P dav Problems 2.5-2.7 P The cross-sectional area of the prismatic bar is A = 0.024 m² and the angle 40°. The average normal stress on the plane P is av 200 kPa. Determine the axial force P and the average shear stress Tav P = 8.18 kN, Tav = -168 kPa.
3 A bar of diameter 25mm has an axial hole 19mm bored out concentric with the outer circumference. The bar is submitted to the following loads simultaneously: (a) An axial tension of 13 kN, (b) A bending moment of 100Nm. Determine the maximum and minimum direct stresses on the section of the bar.
A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5 MPa. The average circumferential (hoop) stress in MPa is
Given the beam and the external loading shown below, if L = 15 m, w1 = 510 N/m and w2 = 1,600 N/m, calculate: • the magnitude and location of the equivalent resultant force (a single equivalent force, for the whole loading block, NOT two equivalent forces from dividing into rectangular and triangular stress blocks). • the reactions at the beam supports. W2 w, A L Resultant force Fr = 单位 (tolerance 1 N, magnitude only) Location xbar = 单位 (tolerance 0.1 m, measured from A) Reactions: Ay = 数字单位 (tolerance 1 N, observe up positive sign convention) MA= 数字单位 (tolerance 10 N*m, observe anti-clockwise positive sign convention)
The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P (in lbs) if the working stresses are 40 ksi for steel and 20 ksi for aluminum, and the total elongation of the bar is not to exceed 0.2
Q4(10 Marks): For the structure shown in the figure, calculate the size of the bolt and the area of the bearing plates required if the allowable stresses are (124 MPa) in tension and 3.44 MPa in bearing. Neglect the weight of the beams. One bolt A 40.03 kN 0.915m 1.83m 0.915 1.83m
The cross section of a concrete pier that is loaded uniformly in compression is shown in the figure. 20 in. (a) Determine the average compressive stress o, in the concrete if the load is equal to 2500 k. (b) Determine the coordinates Fand ỹ of the point where the resultant load must act in order to produce uniform normal 16 in. stress. 48 in. 16 in. 16 in. OL 20 in. 16 in.
The cross section of a reinforced concrete beam is shown below. It has a modular ratio of 15. If the allowable compressive stress in the concrete is 6 MPa and the allowable tensile stress in the steel is 120 MPa, determine diameter of the three reinforcing steel rods to make the beam an economic section.
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 7 mm in diameter. Assume a = 560 mm, b = 280 mm, h = 450 mm, and 0= 70%. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 140 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a Answer: Pmax= i B KN
3. An axial pull of 35000 N is acting on a bar consisting of three lengths as shown below. If the Young's Modulus is 2.1 x 105 N/mm2. Determine (i) Stresses in each section, and; (ii) Total extension of the bar. Section 3 Section 2 Section 1 35000 N 35000 N 2 cm DIA 3 cm DIA 5 cm DIA k-20 cm- 25 cm -22 cm-